Engine Mechanical (5Vz-Fe) Service Data - Toyota T100 1996 Service Manual

ENGINE MECHANICAL (5VZ−FE)
SERVICE DATA
Compression
pressure
Difference of pressure between each cylinder
Valve
clearance
Adjusting shim for repair part
Ignition timing
Idle speed −
Intake manifold
vacuum
Timing belt Protrusion from housing side
tensioner
Cylinder head Warpage
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter
Valve guide Inside diameter
bushing Outside diameter for repair part
Valve Valve overall length
Valve face angle
Stem diameter
Stem oil clearance
Margin thickness
1996 TOYOTA T100 (RM449U)
SERVICE SPECIFICATIONS
at 250 rpm STD
w/ Terminals TE1 and E1 connected of DLC1 8 − 12° BTDC @ idle
Minimum Intake
Maximum Intake
− ENGINE MECHANICAL (5VZ−FE)
1,200 kPa (12.2 kgf/cm
Minimum 1,000 kPa (10.2 kgf/cm
100 kPa (1.0 kgf/cm
at cold Intake 0.13 − 0.23 mm (0.006 − 0.009 in.)
Exhaust 0.27 − 0.37 mm (0.011 − 0.014 in.)
Mark 2.500 2.500 mm (0.0984 in.)
Mark 2.550 2.550 mm (0.1004 in.)
Mark 2.600 2.600 mm (0.1024 in.)
Mark 2.650 2.650 mm (0.1043 in.)
Mark 2.700 2.700 mm (0.1063 in.)
Mark 2.750 2.750 mm (0.1083 in.)
Mark 2.800 2.800 mm (0.1102 in.)
Mark 2.850 2.850 mm (0.1122 in.)
Mark 2.900 2.900 mm (0.1142 in.)
Mark 2.950 2.950 mm (0.1161 in.)
Mark 3.000 3.000 mm (0.1181 in.)
Mark 3.050 3.050 mm (0.1201 in.)
Mark 3.100 3.100 mm (0.1220 in.)
Mark 3.150 3.150 mm (0.1240 in.)
Mark 3.200 3.200 mm (0.1260 in.)
Mark 3.250 3.250 mm (0.1280 in.)
Mark 3.300 3.300 mm (0.1299 in.)
700 ± 50 rpm
at idle speed 60 kPa (450 mmHg, 17.7 in.Hg) or more
10.0 − 10.8 mm (0.394 − 0.425 in.)
Maximum 0.10 mm (0.039 in.)
30°, 45°, 60°
45°
1.0 − 1.4 mm (0.039 − 0.055 in.)
STD 10.985 − 11.027 mm (0.4325 − 0.4341 in.)
O/S 0.05 11.050 − 11.077 mm (0.4350 − 0.4361 in.)
6.010 − 6.030 mm (0.2366 − 0.2374 in.)
STD 11.033 − 11.044 mm (0.4344 − 0.4348 in.)
O/S 0.05 11.083 − 11.094 mm (0.4363 − 0.4368 in.)
STD Intake 95.15 mm (3.7461 in.)
Exhaust 94.90 mm (3.7362 in.)
94.60 mm (3.7244 in.)
Exhaust 94.40 mm (3.7165 in.)
44.5°
Intake 5.970 − 5.985 mm (0.2350 − 0.2356 in.)
Exhaust 5.965 − 5.980 mm (0.2348 − 0.2354 in.)
STD Intake 0.025 − 0.060 mm (0.0010 − 0.0024 in.)
Exhaust 0.030 − 0.065 mm (0.0012 − 0.0026 in.)
0.08 mm (0.0031 in.)
Exhaust 0.10 mm (0.0039 in.)
STD 1.0 mm (0.039 in.)
Minimum 0.5 mm (0.020 in.)
Author :
2
, 174 psi)
2
, 145 psi)
2
, 15 psi) or less
Date :
SS−9
SS00O−07
183