Toyota T100 1996 Service Manual page 191

Connecting Thrust clearance
rod
Connecting rod bearing center wall thickness
Reference
Connecting rod oil clearance
Rod bend
Rod twist
Bushing inside diameter
Piston pin diameter
Bushing oil clearance
Connecting rod bolt outer diameter
Crankshaft Thrust clearance
Thrust washer thickness
Main journal oil clearance
Main journal diameter
Main bearing center wall thickness
Reference
Crank pin diameter
Circle runout
Main journal taper and out−of−round
Crank pin taper and out−of−round
1996 TOYOTA T100 (RM449U)
SERVICE SPECIFICATIONS
Maximum per 100 mm (3.94 in.)
Maximum per 100 mm (3.94 in.)
Others STD
No.1 Mark 1
Others Mark 1
− ENGINE MECHANICAL (5VZ−FE)
STD 0.150 − 0.330 mm (0.0059 − 0.0130 in.)
Maximum 0.380 mm (0.0150 in.)
Mark 1 1.484 − 1.488 mm (0.0584 − 0.0586 in.)
Mark 2 1.488 − 1.492 mm (0.0586 − 0.0587 in.)
Mark 3 1.492 − 1.496 mm (0.0587 − 0.0589 in.)
STD 0.024 − 0.053 mm (0.0009 − 0.0021 in.)
O/S 0.25 0.023 − 0.069 mm (0.0009 − 0.0027 in.)
Maximum 0.08 mm (0.0031 in.)
0.05 mm (0.0020 in.)
0.15 mm (0.0059 in.)
22.005 − 22.017 mm (0.8663 − 0.8668 in.)
21.997 − 22.009 mm (0.8660 − 0.8665 in.)
STD 0.005 − 0.011 mm (0.0002 − 0.0004 in)
Maximum 0.05 mm (0.0020 in.)
STD 7.860 − 8.000 mm (0.3094 − 0.3150 in.)
Minimum 7.600 mm (0.2992 in.)
STD 0.020 − 0.220 mm (0.0008 − 0.0087 in.)
Maximum 0.300 mm (0.0118 in.)
2.440 − 2.490 mm (0.0961 − 0.0980 in.)
No.1 STD 0.020 − 0.038 mm (0.0008 − 0.0015 in.)
U/S 0.25 0.019 − 0.059 mm (0.0007 − 0.0023 in.)
0.024 − 0.042 mm (0.0009 − 0.0017 in.)
U/S 0.25 0.023 − 0.063 mm (0.0009 − 0.0025 in.)
Maximum 0.08 mm (0.0031 in.)
STD 63.985 − 64.000 mm (2.5191 − 2.5197 in.)
U/S 0.25 63.745 − 63.755 mm (2.5096 − 2.5100 in.)
1.991 − 1.994 mm (0.0784 − 0.0785 in.)
Mark 2 1.994 − 1.997 mm (0.0785 − 0.0786 in.)
Mark 3 1.997 − 2.000 mm (0.0786 − 0.0787 in.)
Mark 4 2.000 − 2.003 mm (0.0787 − 0.0789 in.)
Mark 5 2.003 − 2.006 mm (0.0789 − 0.0790 in.)
1.989 − 1.992 mm (0.0783 − 0.0784 in.)
Mark 2 1.992 − 1.995 mm (0.0784 − 0.0785 in.)
Mark 3 1.995 − 1.998 mm (0.0785 − 0.0787 in.)
Mark 4 1.998 − 2.001 mm (0.0787 − 0.0788 in.)
Mark 5 2.001 − 2.004 mm (0.0788 − 0.0789 in.)
STD 54.987 − 55.000 mm (2.1648 − 2.1654 in.)
U/S 0.25 54.745 − 54.755 mm (2.1553 − 2.1557 in.)
Maximum 0.06 mm (0.0024 in.)
Maximum 0.02 mm (0.0008 in.)
Maximum 0.02 mm (0.0008 in.)
Author :
SS−11
Date : 185