Toyota T100 1996 Service Manual page 227

Output shaft snap ring thickness
Reverse gear
Coutner gear snap ring thickness
Front bearing
Counter gear snap ring thickness
No.3 clutch hub
Counter gear snap ring thickness
Rear bearing
Oil seal drive in depth
Front bearing retainer (from retainer end)
Extension housing
Speedometer drive gear
1996 TOYOTA T100 (RM449U)
SERVICE SPECIFICATIONS
Mark 11
Mark 12
Mark 13
Mark 14
Mark 15
Mark 16
Mark 17
Mark 18
Mark 19
Mark 20
Mark 21
Mark 22
Mark 23
− MANUAL TRANSMISSION (W59)
Mark 5 2.25 − 2.30 mm (0.0886 − 0.0906 in.)
2.30 − 2.35 mm (0.0906 − 0.0925 in.)
2.35 − 2.40 mm (0.0925 − 0.0945 in.)
2.40 − 2.45 mm (0.0945 − 0.0965 in.)
2.45 − 2.50 mm (0.0965 − 0.0984 in.)
2.50 − 2.55 mm (0.0984 − 0.1004 in.)
2.55 − 2.60 mm (0.1004 − 0.1024 in.)
2.61 − 2.66 mm (0.1028 − 0.1047 in.)
2.67 − 2.72 mm (0.1051 − 0.1071 in.)
2.73 − 2.78 mm (0.1075 − 0.1094 in.)
2.79 − 2.84 mm (0.1098 − 0.1118 in.)
2.85 − 2.90 mm (0.1122 − 0.1142 in.)
2.91 − 2.96 mm (0.1146 − 0.1165 in.)
2.97 − 3.02 mm (0.1169 − 0.1189 in.)
Mark A 2.05 − 2.10 mm (0.0807 − 0.0827 in.)
Mark B 2.10 − 2.15 mm (0.0827 − 0.0846 in.)
Mark C 2.15 − 2.20 mm (0.0846 − 0.0866 in.)
Mark D 2.20 − 2.25 mm (0.0866 − 0.0886 in.)
Mark E 2.25 − 2.30 mm (0.0886 − 0.0906 in.)
Mark F 2.30 − 2.35 mm (0.0906 − 0.0925 in.)
Mark G 2.35 − 2.40 mm (0.0925 − 0.0945 in.)
Mark 2 2.06 − 2.11 mm (0.0811 − 0.0831 in.)
Mark 3 2.12 − 2.17 mm (0.0835 − 0.0854 in.)
Mark 4 2.18 − 2.23 mm (0.0858 − 0.0878 in.)
Mark 5 2.24 − 2.29 mm (0.0882 − 0.0902 in.)
Mark 1 1.90 − 1.95 mm (0.0748 − 0.0768 in.)
Mark 2 1.96 − 2.01 mm (0.0772 − 0.0791 in.)
Mark 3 2.02 − 2.07 mm (0.0795 − 0.0815 in.)
Mark 4 2.08 − 2.13 mm (0.0819 − 0.0839 in.)
Mark 5 2.14 − 2.19 mm (0.0843 − 0.0862 in.)
Mark 6 2.20 − 2.25 mm (0.0866 − 0.0886 in.)
Mark 7 2.26 − 2.31 mm (0.0890 − 0.0909 in.)
12.2 ± 0.5 mm (0.480 ± 0.020 in.)
0 ± 0.5 mm (0 ± 0.020 in.)
25 mm (0.98 in.)
Author :
SS−47
Date : 221