Toyota T100 1996 Service Manual page 224

SS−44
Output shaft snap ring thickness
Rear
Counter gear roller bearing journal diameter
Counter 5th gear thrust clearance
Counter 5th radial clearance
Reverse idler gear radial clearance
Reverse idler gear to shift arm clearance
Counter gear snap ring thickness
Front
Counter gear snap ring thickness
Rear
Oil seal drive in depth
Speedometer driven gear
Front bearing retainer (from retainer end)
Extension housing
Transfer adaptor
1996 TOYOTA T100 (RM449U)
SERVICE SPECIFICATIONS
Mark M
− MANUAL TRANSMISSION (R150, R150F)
Mark A 2.65−2.70 mm (0.1043−0.1063 in.)
Mark B 2.70−2.75 mm (0.1063−0.1083 in.)
Mark C 2.75−2.80 mm (0.1083−0.1102 in.)
Mark D 2.80−2.85 mm (0.1102−0.1122 in.)
Mark E 2.85−2.90 mm (0.1122−0.1142 in.)
Mark F 2.90−2.95 mm (0.1142−0.1161 in.)
Mark G 2.95−3.00 mm (0.1161−0.1181 in.)
Mark H 3.00−3.05 mm (0.1181−0.1201 in.)
Mark J 3.05−3.10 mm (0.1201−0.1220 in.)
Mark K 3.10−3.15 mm (0.1220−0.1240 in.)
Mark L 3.15−3.20 mm (0.1240−0.1260 in.)
3.20−3.25 mm (0.1260−0.1280 in.)
Mark N 3.25−3.30 mm (0.1280−0.1299 in.)
Mark P 3.30−3.35 mm (0.1299−0.1319 in.)
Mark Q 3.35−3.40 mm (0.1319−0.1339 in.)
Mark R 3.40−3.45 mm (0.1339−0.1358 in.)
Mark S 3.45−3.50 mm (0.1358−0.1378 in.)
Min. 27.860 mm (1.0968 in.)
STD 0.10−0.35 mm (0.0039−0.0138 in.)
Max. 0.40 mm (0.0157 in.)
STD 0.015−0.068 mm (0.0006−0.0027 in.)
Max. 0.160 mm (0.0063 in.)
STD 0.040−0.082 mm (0.0016−0.0032 in.)
Max. 0.130 mm (0.0051 in.)
STD 0.05−0.35 mm (0.0020−0.0138 in.)
Max. 0.50 mm (0.0197 in.)
Mark A 2.00−2.05 mm (0.0787−0.0807 in.)
Mark B 2.05−2.10 mm (0.0807−0.0827 in.)
Mark C 2.10−2.15 mm (0.0827−0.0846 in.)
Mark D 2.15−2.20 mm (0.0846−0.0866 in.)
Mark E 2.20−2.25 mm (0.0866−0.0886 in.)
Mark F 2.25−2.30 mm (0.0886−0.0906 in.)
Mark A 2.80−2.85 mm (0.1102−0.1122 in.)
Mark B 2.85−2.90 mm (0.1122−0.1142 in.)
Mark C 2.90−2.95 mm (0.1142−0.1161 in.)
Mark D 2.95−3.00 mm (0.1161−0.1181 in.)
Mark E 3.00−3.05 mm (0.1181−0.1201 in.)
Mark F 3.05−3.10 mm (0.1201−0.1220 in.)
Mark G 3.10−3.15 mm (0.1220−0.1240 in.)
25 mm (0.98 in.)
11.7 ± 0.5 mm (0.461 ± 0.020 in.)
0 ± 0.5 mm (0 ± 0.020 in.)
45.6 ± 0.5 mm (1.795 ± 0.020 in.)
Author :
218
Date :