Data Dump Mode - Toshiba Strata DK 280 Installation Manual

2. Place the terminal into the program mode per
Section 13.7-Selecting a Mode.
3. Program procedures are categorized and given in
the order below. Use these procedures to store
System Record Sheet data in working memory.
initialization procedures:
These procedures must be completed
whenever a system is first installed.
Type 1 programs:
10-1, 10-2, 10-3, 15, 16, 42-0, 46-11, 46-21,
46-31, 46-41, 46-51, 46-61, 46-71, 46-81, 58-
1, 58-2, 77-1, 77-2.
Type 2 programs:
Station Class of Service:
17, 20, 30, *30, 31, *31, 35, 40, 41, *41-1
43, 60-8, 79, 81 - 89.
Type 3 programs:
0
Initialization: 90, 91, 91-9, 92.
l
General: 00, 03, 04, 05, 3cO9, 12, 13,
t415, Jc17, 19, *29, 21, 22, 27, 28, 29,
32, 33, 34, 36, 37, 38, 39, Jc41-2, 3c41-3,
Jc42, 42-1 - 8, 44, 60, 69, 70, 77-3, 78,
80, 93.
l
Toll Restriction: 45 - 48.
0
Least Cost Routing: 50 - 56.
l
Auto Attendant: 09, 1 O-3, 23, 24, 25-1, 26.
13.9 Data Dump Mode
This mode allows four types of data to be displayed or
output to a printer: Strata DK280 Programs (Customer
Data Base), Speed Dialing Numbers (Station/System),
LCD Messages (Station/System), and Ti RDTU PCB
error checks.
H Initialization: 90, 91, 91-9, 92.
4 General: called: Program Dump, Speed Dialing
Dump, LCD Messages Dump, and Tl Error Dump.
Program Dump: While in the Dump mode, type
PRG, followed by the program number (up to seven
characters), then press Enter. The alphanumeric
characters represent a program group or a particular
program, i.e., ALL, 03, 04, IO, 39, etc., or group range
(XX * YY) where XX (or *XX) is the low program
number and YY (or *YY) is the high program number.
For a printout example, see Figure 13-6.
Note:
Programs are output only in the groups
indicated. To print out or review a program not
included above,
use Program Mode
procedures.
Speed Dialing Dump: While in the Dump mode, enter
REP, three characters, then press Enter. The
characters represent the Speed Dialing codes for
either an individual station port (000 - 239), A L L (all
stations and system data) or S Y S (system data only):
PROGRAM NUMBER
PORT NUMBER
## SYSTEM PROGRAMMING ##
1: SELECT (LED ON)
40 3332 25
24 17 16 9 8 '+
81 000 11111111 11111111
11111111 11111111 NUMBERS
CO LINE
11111111
11111111 11111111 11111111 11111111 111111114-L~NES4~-8(~
11111111 11111111
11111111 11111111 11111111+L~NES81-~20
11111111 11111111 11111111
144 131136 12 9128 12 I+-
CO LINE NUMBERS
40 3332 25
24 11 16 9 8 1
81 001-249 0 0 0 0 0 0 0 o 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000
00000000 00000000 00000000
144 13 7136 12 9128 121
## END OF PRINT
Figure 13-6
Data Dump Printout Example
##
DK,
,488
13-12
January1996