Toshiba Strata DK 280 Installation Manual page 397

Code #271) for this feature to work. Tenant
assignments are made in Program *15.
Program 77-4, LED Ol/LED 02-RSIU Open
Architecture (OA) Data Output Assignments
(Caller ID/DNIS/ANI/OA Output Options)
This program is used to enable Caller ID, Automatic
Number Identification (ANI), and/or Dialed Number
Identification Service (DNIS) Numbers (received) to be
sent from the RSIU Open Architecture (OA) port. The
OA port sends MIS data for ACD calls (only) along
with ANI, Caller ID and/or DNIS Numbers received on
ACD calls depending on LED 01 and LED 02 option
settings. ANI, Caller ID and/or DNIS numbers on non-
ACD calls will not be sent out the OA port for non-ACD
calls.
Turn LED 01 ON if the OA port should send Caller ID
and/or ANI information for ACD calls.
Turn LED 02 ON if the OA port should send DNIS
Number (not DNIS NAME) for ACD calls.
Note:
1. Program 77-4 allows LED 01 and LED 02
to be turned ON simultaneously to allow
Caller ID, ANI, and DNIS numbers
received on ACD calls to be sent from the
OA port.
2. The system will initialize with LED 01 and
02 OFF - no ACD Caller ID, ANI, or DNIS
information will be sent from the OA port
Program 78-Ground/Loop Start CO Line Special
Ringing Assignments
n
n
Ring Over External Page During Night Mode,
n Door Phone Ring, LEDs 01 m 12-When a door
Feature I-This program selects which
phone button is pressed, selected digital and/or
ground/loop start CO lines will activate ringing
electronic telephones will ring as assigned with
over external paging facilities during the NIGHT
this program.
See Program 77-2 for an
mode (for Tenants 1 - 4). The NT Relay on the
explanation of the door phone A, B, and C
PIOU, PIOUS, or PEPU will also be activated if it
numbering scheme. (See Program *79 for door
is in the 1 -second ON/3-seconds OFF mode.
phone to [DN] flashing assignments.)
DISA CO Line Assignment, Feature 2-This
program assigns ground/loop start CO lines to be
used with the Direct Inward System Access
(DISA) features. These lines may be set for DISA
operation during the different system modes of
DAY, DAY2 and NIGHT. A line will switch to
normal ringing after ten seconds if the outside
caller does not use the DISA feature. Normal
function of these lines occurs for outgoing calls.
Note:
An optional security code for DISA
outgoing
lines calls is available via Program 608.
q Ring IMDU or RMDS Maintenance Modem,
Feature 5-The IMDU or RMDS Remote
Maintenance modem can be directly accessed by
incoming ground/loop start CO lines assigned in
this Program. Different alternatives are available
for the system modes of DAY, DAY2, and NIGHT.
If none of these are selected, the IMDU or RMDS
can still be reached by dialing a modem [DN] with
the DISA feature or by a Ring Transfer from the
,DSS console attendant or any other station. The ,
IMDU or RMDS modem must be enabled with :r
Program 77-1, LED 14-ON.
H Built-in Auto Attendant CO Line Assignment,
Feature 6-This feature selects ground/loop start
CO lines for Auto Attendant operation. There is no
limit to the number of lines which can be assigned
with Auto Attendant. Different alternatives are
available for system modes DAY, DAY2, and
NIGHT.
Program 79-Door Phone Ringing
(Initialized data reads all LEDs OFF.)
n Muted Ring to Busy Electronic and Digital
Telephone, LED 20-If all electronic and digital
telephones are busy and a door phone button is
pressed, a muted ring tone can be sent to
selected digital and electronic telephones, as
defined with this program. (Only the lowest port in
the appropriate ringing group will mute ring.)
Program *79-Door Phone to [DN] Flashing
Assignments
Door phones can be assigned to ring and flash
Directory Number buttons/LEDs ([PDNs]/[SDNs], and
[PhDNs]). This program assigns which [DN] will flash
when a door phone button is pressed to ring a .
Program 79 must be used in conjunction with Program
*79 to cause the telephone (on which the -flashing
[DN] appears) to ring when the door phone button is
pressed. Each door phone can be assigned to flash
January 1996
9-37