Basic System Records - Toshiba Strata DK 280 Installation Manual

have been caused by the common control unit (RCTU:
A, Et, BA/BB, and C/D) jumper movement to the
internal battery.
Initialized data information is at the bottom of each
System Record Sheet. If the system is being installed
in a new location, all programs should be initialized.
Since running Program 91-9 automatically runs
Program 90, this program can be skipped if Program
91-9 is run.
Program 91-I -Automatic PCB Recognition and
Port Renumber
Automatically makes PCB slot code assignments
I
during an initial installation - after all of the PCBs have
been installed . This program only applies to slots in
which non-optioned PCBs are installed-such as the
PDKU without a Data Interface Unit or Off-hook Call
Announce (OCA), the common control unit (RCTU: A,
B, BA/BB and C/D) without a Dual-tone Multi-
frequency Receiver (RRCS), etc. For slots that have
PCBs equipped with options, Program 03 must be run
after Program 91-l.
Program 91-1 can be run after PCB option codes have
been set with Program 03; it will not erase option
codes. Program 91-1 will also set physical port and
logical ports to the initialized settings. (See Program
01 and 02 for initialized settings.) If station ports have
been relocated, they will be located back to the
system default logical to physical assignments after
running Program 91-l. Since running Program 91-9
automatically runs Program 91-1, this program can be
skipped if Program 91-9 is run.
Program 91-2-Data Transfer from Temporary
Memory to Working Memory
Provided with DK280 R3 and above. Data on a few
selected DK280 Programs is placed in Temporary
Memory when a Data change is made. To transfer the
data change information to Working Memory, it is
necessary to run Program 91-2 (locally or remotely);
or, turn the DK280 power off for 5 sec. and then back
on. The Programs that require this data memory
transfer process are listed on the Program 91-2 record
sheet.
CAUTION !
Running Program 91-2 will drop all calls and
interrupt telephone service for about 10
seconds.
Note:
Running Program 9 l-2 will not change or
erase any customer data.
Program 924nitializing Speed Dial Numbers,
VM ID Codes, Character Message Memory, Timed
Reminders, Digital Telephone Volume, Called ID,
ANI, and Call Forward Backup RAM
All previously entered or random data (of the type
listed) is cleared by this program. This program must
be run when first installing a system or a common
control unit (RCTU: A, B, BA/BB, and C/D). Since
running Program 91-9 automatically runs Program 92
(1 - 9) this program can be skipped if Program 91-9 is
run.
9.2 Basic System Records
Program 00, Part
1 -Software
Check/Remote
Maintenance Security Code Assignments
n
Code 0, ROM Version-Code
0 displays the
software version of the system common control
unit (RCTUA, RCUTB, RCTUBA/RCTUBB and
RCTUCIRCTUD) and if installed on the RCTU, the
RKYS key type. See the Program 00 Record
Sheet for an illustration of software displays. This
information cannot be altered with this program.
n
Code 1, Level 1 Security Code-Use
this
program to assign a Remote Maintenance security
code that allows entry to all programs and data.
I
n
Code 2, Level 2 Security Code-Use
this
program to assign a Remote Maintenance security
code that allows entry to Programs 30 - 39, 77 -
89, and *30 - *31.
IMPORTANT !
When using a 280Admin PC, either Security
Code (1 or 2) enables the 280Admin user full
access to all Strata DK280 programs. Always
change Security Code 1 and Code 2 to
prevent unauthorized programming changes
by 280Admin users that may try to log-in
remotely with the default security code: 0000.
9 Code 8, Software RAM Checksum-For
factory
purposes only.
q
Code 9, Power OFF Counter-For
factory
purposes only.
9-2
January 1996