13.2 General Description; Hardware Requirements - Toshiba Strata DK 280 Installation Manual

13.2 General Description
Remote Administration and Maintenance is
accomplished with a remote ASCII terminal/modem
communicating over the public telephone network via
either an external modem (connected to a dedicated
CO line or a standard telephone port) or a modem unit
(IMDU) installed on a PIOU or PIOUS PCB or an
RMDS installed on a RSIU PCB-Release 3 and
above. See Figures 13-2 - 13-5.
Note:
Using an ASCII terminal for Remote
Maintenance (RM) is not recommended.
Toshiba recommends that a 280Admin PC be
used for RM.
Remote Administration and Maintenance calls may
connect to the IMDU or RMDS automatically via
programmable CO line ringing assignments (Program
78) for ground/loop start lines or via Program *09 or
71-1 (l-3) for DID/tie/DNIS lines, or manually via the
standard call transfer feature at Directory Number #19.
Automatic connection allows remote programming to
be accomplished after business hours without on-site
assistance via night ringing assignments.
Remote Administration and Maintenance allows the
following functions to be accomplished remotely:
Program Mode
provides for complete programming of
all Strata DK280 programs (including Speed Dial
adds/changes).
Test Mode
provides for testing of Strata DK280
stations and CO lines.
Data Dump Mode
provides a complete printout of all
or individual Strata DK280 customer database
programs, including Speed Dial numbers and LCD
messages.
Message Mode provides for sending, adding, or
changing digital and electronic telephone LCD
messages.
Speed Dial Mode
allows Station and System Speed
Dial numbers to be programmed remotely.
280Admin/280Backup
allows program download,
upload and/or editing of DK280 system programs,
System Speed Dial, Personal Speed Dial, LCD
messages, voice mail codes and more. 280Admin or
280Backup requires a personal computer with Toshiba
280Admin or 280Backup software and an operating
key connected to the LPT2 port of the PC. This
section of the DK280 I&M manual does not provide
instructions regarding the use of 280Admin or
280Backup-refer to the 280Admin or the 280Backup
User Guides.
n
n
n
Program Download 280Admin and 28OBackup
allows the database which is stored on a DK280
RCTU PCB to be sent to (and stored on) a
Personal Computer disk. To download an RCTU
database to a PC disk, the RCTU must be
operating in a DK280 base cabinet; and the PC
must have the Toshiba 280Admin or 280 Backup
software installed. Also, an RSIU, RSSU, PIOU or
PIOUS must be installed in any cabinet.
Program Upload 280Admin and 280Backup
allows the database which is stored on a PC disk
to be sent to (and stored in) the RAM of an RCTU
PCB. To upload an RCTU database from a PC
disk, the same requirements necessary for
program download are needed.
Edit of customer database can be accomplished
via 280Admin PC software (not 280Backup) on- or
off-line with the DK280. Refer to the 280Admin
User Guide for more information.
There are two levels of Remote Administration and
Maintenance protected by a security code defined in
Program 00.
Level 1
allows access to all programs.
Level
2 allows access to Programs 30 - 39 and
77 - 89, which pertain only to individual station
options such as button assignments, Class of Service,
etc.
Each Remote Administration and Maintenance level
has a different programmable password for customer
database protection. This allows a customer to make
certain station moves, adds, and changes in Level 2;
while protecting the critical system assignments in
Level 1 (refer to Program 00).
13.3 Hardware Requirements
The Strata DK280 must be configured with either an
IMDU-equipped PIOU or PIOUS, a RMDS-equipped
RSIU, or an external modem connected to a dedicated
CO line or standard telephone circuit. (A modem is not
required for local, on-site, maintenance.)
1 -z1-3
lanuarv 1996