Toshiba Strata DK 280 Installation Manual page 393

sent to the voice mail machine when the DNIS/tie/
DNIS extension or ANI call forwards to VM. This
program can also be used with non-DNIS tie and/or
DID lines to assign VMID digits to normal tie or DID
numbers.
The last address (499 for RCTUC3/D3, 349 for
RCTUBA3/B3, and 199 for RCTUA3) in Program 71-4
can be used to assign a VMID code to ANI only lines.
All ANI only lines will be directed to the same Voice
Mailbox.
To assign an ANI only tie/DID line to Program 71-4
assignments: Program 17, LED 05 must be turned
OFF and LED 07 and 08 must be ON for lines that
k
receive ANI digits only.
Program 71-5- Dialed Number identification
Service (DNIS) Number Name Display
This program is used to assign names to each DNIS
number. The names for each DNIS/tie/DID extension
number is normally supplied by the customer. Each
DNIS name can be up to 16 alphanumeric characters.
The DNIS/tie/DID extension name will display on a
telephone's LCD when the DNIS/tie/DID extension
number rings the telephone directly or is transferred,
Call Forwarded, or Hunted to the telephone.
To assign a tie/DID line to Program 71-5 assignments:
Program 17, LED 05 must be turned ON for lines that
should display DNIS/tie/DID extension name tags.
When a tie/DID line receives both DNIS and ANI digits
on the same call, Program 17, LED 06 determines
what information, DNIS extension name or ANI
number, will display as a priority when the line rings
incoming to the DK280.
This program can also be used with non-DNIS or ANI
tie and/or DID lines to display names, associated with
the tie or DID numbers, on telephone LCDs. In this
case, the normal tie digit assignments in Program 04
and/or DID digit assignments in Program *09 will not
be active.
IMPORTANT!
1. An individual telephone user can
disable/enable the DNIS name display by
using the Mode 60/61 function on his/her
LCD telephone.
2. The DNIS extension name can be
assigned or not assigned to display as
a
priority over the ANI display (in Program
17, LEDOG) when both ANI and DNIS
digits are received on the same call.
3. If a name is not assigned to a DNIS
number, DN:XXXX will display on
telephone LCDs when the DNIS/tie/DID
line rings into the DK280 system (where
XXXX = actual DNIS/tie/DID digits
received).
Program *71, *72, *73-[DNI to [DNI, Tie to
[DN], and DID to
[DNI
Ringing Assignments
Primary/Secondary/Phantom Directory Number and
DH Group Telephone Ringing assignments:
n
n
w
This program assigns telephones to ring when a
,
[PDN], [SDN],
or
[PhDN]
that appears on the
'
telephone is dialed from another telephone (direct
or transferred call).
This program assigns telephones to ring when a
call is routed from a tie, DID, DNIS, DNIS/ANI or
ANI only line to a
[PDN], [SDN],
or
[PhDN]
that
appears on the telephone.
This Program assigns telephones to ring when a
[PDN]
or
[SDN]
that appears on the telephone is
included in a Distributed Hunt Group (DK280
Release 3.1 and above).
IMPORTANT!
120 Telephones (maximum) can be
programmed to ring for any given [PDN]/
[SON] or [PhDN] in Program *71, *72, and
*73 combined.
For the above case:
n
Telephones can be programmed to immediately
Ring (*71 assignments), delay ring after 12
seconds (*72 assignments), or delay ring after 24
seconds (*73 assignments) for each
[PDN],
[SDN],
or
[PhDN]
button that appears on the
telephone.
n
The called
[PDN], [SDN],
or
[PhDN]
button must
be programmed to appear (Program 39) on all
Telephones that should ring.
n
Default (Initialized) assignments are:
[PDNs]
are
Programmed to immediately ring their respective
telephones in Program *71; no other default
ringing assignments are made. Example:
[PDN]200
will ring the telephone connected to
logical Port 000. (Program 04 000 = 200. 200 is
the default
[PDN]
for logical Port 000).
January 1996
9-33