Toshiba Strata DK 280 Installation Manual page 392

Each of the DK280 RCTU, Release 3, processors
supports a different quantity of DNIS or DID/tie line
extension numbers as follows: RCTUC3/D3 - 500
DNIS numbers, RCTUBA3/B3 - 350 DNIS numbers,
and RCTUA3 - 200 DNIS numbers.
n
Outside telephone number routed externally over
the Public Telephone Network
n
The DK280 system remote maintenance -modem
To assign a DNIS and/or normal tie/DID line to
Program 70-O assignments: Program 17, LED 05 must
be turned ON for the line. In this case, tie lines do not
follow Program 04 assignments and DID lines do not
follow Program *09 assignments. When this program
is used with normal (non-DNIS or non-ANI) tie and/or
DID Lines -Program 17, LEDs 06,07, and 08 must be
OFF.
n
Night ringing over the DK280 external page
q The DK280 external voice paging system (Private
Network tie lines only)
Program 71 -(l - 3)-DNIS Number and ANI Line
,
Routing Assignments
Assigns the routing destination of each DNIS and/or
normal tie/DID line extension number and/or the
routing destination of Automatic Number Identification
(ANI) only lines.
A DNIS number or ANI only line can be assigned to
route to one destination only in each of the three
system ringing modes (Day, Day2 and Night); the
destination can be unique or different in each ringing
mode. For each DNIS tie/DID extension number, the
routing destination can be a unique destination or it
can be the same destination as that assigned to other
DNIS numbers. To assign lines that receive both ANI
and DNIS with each call to Program 71-1
assignments: Program 17, LED 05,07 and 08 must be
turned ON for lines that receive DNIS digits only, LED
05 and 08 must be ON.
IMPORTANT!
Program 71- 1 only assigns DNIS numbers to
route to selected [DN] buttons and makes
them flash when the DNIS number is called.
When assigning DNlS numbers to
route
to
Directory Numbers ([PDNs], [SDNs],
[PhDNs]) using program 71-1, Program *71,
*72, and *73 must also be used to assign the
telephones, on which the [DNs] appear, to
ring. When assigning DNIS numbers to route
to ACD and DH groups using Program 71, the
telephones (and appropriate [PDN], [SDN], or
[PhDN]) in these groups must also be
assigned to ring in Program *71, *72, and
*73.
This program can also be used with non-DNIS or non-
ANI tie and/or DID lines to route calls. In this case, the
normal Tie digit assignments in Program 04 and DID
digit assignments in Program *09 will not be active -
Program 17, LED 06, 07, 08 must be OFF and LED
05 must be ON for normal tie/DID lines.
The last address (499, 349, or 199) in Program 71-O is
used to assign ANI only lines to a routing destination.
All ANI only lines must be assigned to the same
routing destination.
To assign an ANI only tie/DID line to Program 71-i
assignments: Program 17, LED 05 must be turned
OFF and LED 07 and 08 must be ON for lines that
receive ANI digits only.
A DNIS and/or tie/DID extension number and/or ANI
Program 71-4 - Dialed Number identification
only line can be assigned to route one of the following
Service (DNIS) Number and ANI Only Lines
destinations:
Voice Mail ID Assignments
n
Primary Directory Number
[PDN]
- secondary
appearances of this
[PDN]
will also ring if
Programmed to ring in Program *71, *72, and/or
*73
i Phantom Directory Number
n
Distributed Hunt Group
0 ACD Group
This Program assigns a Voice Mailbox ID (VMID)
number to each DNIS/tie/DlD extension number
and/or ANI only lines. This allows each DNIS/tie/DID
extension number and/or ANI only lines to be routed to
a unique Voice Mail box when the number directly
rings or is Call Forwarded to the Voice Mail system.
When a DNIS/tie/DID extension number or ANI line
rings a station that has call forwarding set to Voice
Mail, the DNIS/tie/DID extension or ANI VMID is sent
to the VM machine (if programmed in Program -71-4).
If a DNIS/tie/DID extension or ANI VMID is not
programmed, the Call Forwarding station's VMID is
9-32
January 1996