Rsiu/Rsis/Rmds Pcb Installation; Pcb - Toshiba Strata DK 280 Installation Manual

numbers. A user can scroll through the stored
abandoned call telephone numbers and auto dial the
selected number using this button.
Program
59,
Code
462-Assigns the CLIIYANI Lost
Call Auto Dial button to the attendant consoles that
store Caller ID and/or ANI abandoned call telephone
numbers. A console user can scroll through the stored
abandoned call telephone numbers and auto dial the
selected number using this button.
Program 10-3, Key 08
n Determines if CLID and/or ANI telephone numbers
will be sent out the system SMDI port:
n Turn LED 08 "On" if the CLID and/or ANI numbers
received should be sent out the system SMDI port.
n Turn LED 08 "Off" if the CLID and/or ANI numbers
received should not be sent out the system SMDI
port.
Note:
The system will initialize with LED 01 "Off",
i.e., no CLID/ANI information will be sent out
the SMDI port.
Program 60-1, Key 01
n Determines which information will be sent out the
system SMDR port, i.e., system Account Codes or
CLID and/or ANI telephone numbers:
H Turn LED 01 "On" if CLID and/or ANI information
should be sent out the system SMDR port.
H Turn LED 01 "Off" if Account Codes information
should be sent out the system SMDR port.
Note:
The system will initialize with LED 01 "Off",
i.e., Account Codes information will be sent
out the SMDR port.
Program 77-4, LED Ol/LED
02 (DK280 Release 3.2
and above)
H Enables CLID, ANI, and/or Dialed Number
Identification Service (DNIS) information to be
sent from the RSIU Open Architecture (OA) port
on ACD calls only:
W Turn LED 01 "On" if the OA port should send CLID
and/or ANI information.
H Turn LED 01 "Off" if the OA port should not send
Caller ID/ANl.
H Turn LED 02 on if the off port should send DNIS
information.
H Turn LED 02 off if the OA port should not send
DNIS information.
Notes:
1. Program 77-4 allows LED 01 and LED 02
to be turned "On" simultaneously to allow
CLID, ANI, and DNIS information to be
sent from the OA port on ACD calls.
2. The system will initialize with LED 01 and
LED 02 ILOW: i.e., no CLID, ANI, or DNIS
information will be sent from the OA poti
on ACD calls.
4.19 RSIU/RSIS/RMDS PCB
Installation
4.19.1 PCB
The RS232/Modem Interface (RSIU) PCB provides up
to four interface ports that allows the DK280 system to
connect to the following hardware devices:
H SMDI or Toshiba Proprietary RS-232 Voice Mail
n ACD SMIS computer
n SMDR printer or SMDR call accounting machine
n 280Admin/280Backup personal computer or
maintenance terminal (locally or remotely)
Open-Architecture application computer system to
receive ANI, DNIS, or CLID digits from the DK280
on ACD calls (DK280 Release 3.2 and above).
The RSIU is a standard plug-in type PCB that must be
installed into the first universal slot of the DK280 base
cabinet. The RSIU PCB provides one standard RS-
232 port (modular jack) when ordered from the factory;
this port can be configured in system programming to
support any one of the hardware options listed above.
The RSIU can be equipped with up to three more
optional RS-232 ports (total of four RS-232 ports) or
with two optional RS-232 ports and one modem port
(total of three RS-232 ports and one modem port). The
optional RS-232 ports are provided by installing RSIS
piggy-back PCBs onto the RSIU PCB. The optional
built-in modem is provided by installing an RMDS
piggy-back PCB onto the RSIU (see Figure 7-38 in
Chapter 7-Wiring Diagrams):
4-58 January 1996