Smdr Hardware Requirements - Toshiba Strata DK 280 Installation Manual

PROGRAM NUMBER
PORT NUMBER
## SYSTEM PROGRAMMING ##
1: SELECT (LED ON)
40 3332 25
24 11 16 9 8
'+
81 000 11111111 11111111
CO LINE NUMBERS
11111111 11111111 11111111
11111111 11111111 11111111 11111111
11111111+LlNES41-80
11111111 11111111 11111111 11111111 1 1 1 1 1 1 1 l+ LINES 81 - 120
11111111 11111111 11111111
144 137136
12 9128 1 2 l4- CO LINE NUMBERS
40 3332 25
24 17 16 9 8
1
81 001-249 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000
00000000 00000000 00000000
144 13 7136 12 9128 121
6
## END OF PRINT ##
DK03:
Figure 6-22
PIOU/PIOUS RSIU/RSIS SMDR Port (Program 97) Data Dump Example
2. If the CPC or AR signal is not sent, the
CO lines will remain seized until the DISA
disconnect timer releases the call (see
Program 12).
Printout C
Auto Release signal: (Release 1 and 2)
003 MSS 12:20 00:00;02 00:06
(outgoing)
003* DISA 12:22 00:02;01 (outgoing)
001 DISA 12:22 00:02;01 (incoming)
Auto Release signal (Release 3 and above)
003 MSS 12:20 00:00;03 00:05 DISA
(outgoing)
*003 DISA
12:22 00:02;01 (outgoing)
001 DISA 12:22 00:02;01 (incoming)
Disconnect Timer (Release 1 and 2)
001 DISA 12:24 00:04;57 (incoming)
003 DISA 12:24 00:04;57 (outgoing)
Disconnect Timer (Release 3 and above)
001 DISA 12:24 00:04;57 (incoming)
003 DISA 12:24 00:04;57 (outgoing)
Note:
The "MSS" entry will print out on/y if the call
was connected after the SMDR threshold, 1.0
or 10 seconds. The threshold is set in
Program 60-2.
System Program Data Printout
If a printer is connected to the SMDR port, customer
program information stored in the RCTU RAM may be
printed out for reference by using Program 97 (see
Subsection 6.7.1, paragraph 3).
6.7.1 SMDR Hardware Requirements
A Strata DK280 system must be equipped with a
PIOU, PIOUS or RSIU (RSIS) PCB to support the
SMDR printer/call accounting device option.
Connection of the printer or call accounting device to
the PIOU, PIOUS or RSIU (RSIS) PCB is
accomplished with a 3-pair modular cord (7 feet
maximum) and a PPTC connector adapter
(Figure 6-23). Call record data is ASCII-formatted, 8
bits, no parity, l-stop bit.
The PIOU, PIOUS or RSIU (RSIS) contains a call
record buffer which stores call record data (for up to
50 calls) when the printed or call accounting device is
turned off, or when no device is connected to the
SMDR port. No further call records are stored after the
buffer is filled. When the printer or call accounting
device is made operational, an "ERROR BUFFER
OVERFLOW" message is printed to indicate that the
buffer was full, and that some call information may
have been lost.
SMDR Programming Considerations
Selectable programming options for the SMDR printer
or call accounting device are as follows:
6-32
January1996