Toshiba Strata DK 280 Installation Manual page 365

announcement voice frequencies are the same as a
DTMF digit and the system RRCS circuit will not dial
or misdials.
The first of the two digits can be either digit 0 or 1 and
must always be the same number for each of the
prompts. Therefore, if the leading digit is assigned as
1, callers could be offered all of the following two-digit
dialing prompts: 10, 11, 12, 13, 14, 15, 16, 17, 18, and
19. See the Record Sheet for Program 09 for detailed
one-digit and two-digit prompt assignment instructions.
Program *09-DID Digit Translation Assignments
This program assigns the routing destinations for
incoming DID line calls. With DK280 Release 1 and 2
RCTU processors, Program *09 DID extension
numbers (the digits the DK280 receives on DID lines
from the local CO or long distance carrier) can be
routed to one telephone only or to an ACD group with
Release 2.
With DK280 Release 3, Program *09 DID extension
numbers can be routed to Primary/Secondary, or
[PhDN], ACD Groups, or Distributed Hunt groups.
Each Primary/Secondary [DN] and/or [PhDN] can
appear and ring (immediate, 12 sec. delay or 24 sec.
delay with Program *71, *72 and *73) on up to 120
telephones. A DID extension number can ring up to
120 telephones maximum with DK280 Release 3
software.
Also, with DK280 Release 3 software, any DID line
can be assigned to route with Program 71 and 72
DNIS routing assignments, instead of Program *09
assignments, to provide all the DNIS call routing
features to normal DID lines.
Which program options (Program *09 or Program 71
and 72) DID line call routing will follow is determined
for each DID line in Program 17, LED 05 (See
Program 17 in the Record Sheet section for more
details).
DID calls will alternately ring all or selected Attendant
Consoles (in the load share group, assigned in
Program 81-89) when a DID Attendant Console
extension number is assigned to ring any one of the
Attendant Console ports in the load share group (see
Chapter 5-Section 5.7.2 for information on Attendant
Console Load Share Programming; see the DK280
ACD I&M manual for ACD DID extension
assignments).
Program 1 O-1 -System Assignments 1
The following options are available on a System-wide
basis: (LEDs 07, 08, 09, 18, 19, and 20 are initialized
as ON.)
n
n
n
n
n
n
n
H
Two-CO Line Conference, LED PO-Two lines
can be conferenced with one or two telephones
(digital, electronic, or standard). Conference (see
LED 19) in this program must be enabled for this
feature to work. Also, Two-line Conference must
be allowed for Direct Inward System Access
(DISA) use of outgoing lines.
Conference, LED 19-The ability of stations to
perform any Conference can be allowed or
disallowed system-wide with LED 19.
Ring Detect Time, LED 18-This should be set to
"normal" unless connected to Central Office/
Centrex lines that send ring signals less than 120
milliseconds.
Station-to-Station Call Volume PAD, LED 17-
ON reduces station-to-station talk path volume (-8
dB). LED 17 should be OFF in all cases except
where extreme quiet room noise is expected.
Automatic Busy Redial ABR Cycles, LED 12-If
activated from an electronic or digital telephone,
Automatic Busy Redial will retry dialing a
telephone number on a line if a far end busy signal
is detected. Turn LED 12 ON to have the system
try up to 10 times; turn OFF for up to 15 attempts.
This feature is not available with standard
telephones.
ABR Redial Time, LED 11-Upon detection of a
far end busy signal on a line, Automatic Busy
Redial will retry either once every 30 seconds or
once every minute. Turn LED 11 ON for 30
seconds; turn OFF for one minute.
System Speed Dial Override, Toll Restriction,
LED lO-System Speed Dial can be chosen to
override Toll Restriction if LED 10 is turned ON.
Exclusive Hold, LED 09-Exclusive Hold allows
electronic and digital telephones to place calls on
hold (by pressing the
Hold
button twice) so that
other stations cannot pick up the held call with a
CO line button. This feature can be disabled on a
system-wide basis. Any station can pick.up an
Exclusive Hold call by using the call pickup code.
January 1996
9-5