Hitachi PC-ARF Technical Catalogue page 697

7 Gateways for building management systems
HARC-BX E
SVNT Unit Variable num-
number number ber
43 6 nviMode_6
nviSet-
44 6
Point_6
nvi-
45 6
FanSpeed_6
46 6 nviProtect_6
47 6 nvoOnOff_6
nvoIn-
48 6
letTemp_6
49 7 nviOnOff_7
50 7 nviMode_7
nviSet-
51 7
Point_7
nvi-
52 7
FanSpeed_7
53 7 nviProtect_7
54 7 nvoOnOff_7
nvoIn-
55 7
letTemp_7
56 Outdoor nviAllOnOff
nciMaxSend-
57
Time
nciMinSend-
58
Time
59 nciPwrUp
HARC-BX(A) XIF file variables list
681 681
TCGB0106 rev.0 - 12/2014
LONMARK
Type
SNVT No.
SNVT_hvac_
108
mode
SNVT_
105
temp_p
SNVT_switch 95
SNVT_switch 95
SNVT_state 83
SNVT_
105
temp_p
SNVT_switch 95
SNVT_hvac_
108
mode
SNVT_
105
temp_p
SNVT_switch 95
SNVT_switch 95
SNVT_state 83
SNVT_
105
temp_p
SNVT_switch 95
107
107
107
Description
1 byte:
1 = HVAC_HEAT (Heat-
ing)
3 = HVAC_COOL (Cool-
Operation mode
ing)
setting
5 = HVAC_PRE_COOL
(Dehumidification)
9 = HVAC_FAN_ONLY
(Ventilation)
2 Bytes: 1700 ~ 3000 = 17
Temperature setting
~ 30 ºC
Byte 1: Value 1: Low,
Value 2: Middle,
Fan speed setting
Value 3: High
Byte 2: State 0 (Fixed)
Byte 1: Value 0 (Fixed)
Byte 2: State 0: RCS
Remote control order
enabled
enabled
State 1: RCS
disabled
32 bits:
ON/OFF state and bit 0: 0 (STOP)/1 (RUN)
alarm notification bit 1: 0 (Normal) /1
(Alarm)
Indoor temperature 2 Bytes: -6200 ~ 12700 =
reading -62 ~ 127 ºC
Byte 1: Value 0 (Fixed)
On/Off order Byte 2: State 0 = STOP
State 1 = RUN
1 byte:
1 = HVAC_HEAT (Heat-
ing)
3 = HVAC_COOL (Cool-
Operation mode
ing)
setting
5 = HVAC_PRE_COOL
(Dehumidification)
9 = HVAC_FAN_ONLY
(Ventilation)
2 Bytes: 1700 ~ 3000 = 17
Temperature setting
~ 30 ºC
Byte 1: Value 1: Low,
Value 2: Middle,
Fan speed setting
Value 3: High
Byte 2: State 0 (Fixed)
Byte 1: Value 0 (Fixed)
Byte 2: State 0: RCS
Remote control order
enabled
enabled
State 1: RCS
disabled
32 bits:
ON/OFF state and bit 0: 0 (STOP)/1 (RUN)
alarm notification bit 1: 0 (Normal) /1
(Alarm)
Indoor temperature 2 Bytes: -6200 ~ 12700 =
reading -62 ~ 127 ºC
Byte 1: Value 0 (Fixed)
On/Off order Byte 2: State 0 = STOP
State 1 = RUN
Condition Note
Approxi-
mate up-
date time of
80 sec.
Allow an in-
terval of at
least 5 sec.
between 2
consecu-
tive orders
to any unit
on a H-Link
Approxi-
mate up-
date time of
80 sec.
The use of
standard
values is
recom-
mended
(do not
change)
7