Canon imageRUNNER ADVANCE C5255 Series Service Manual page 943

COPIER > ADJUST > FEED-ADJ
REG-DUP1 Rgst start timing adj: Plain, 2nd side
Lv.1 Details To adjust the leading edge margin by changing the timing to turn ON
the Registration Motor when feeding the second side of plain paper.
As the value is incremented by 1, the margin on the leading edge of
paper is increased by 0.1 mm.
+: Leading edge margin becomes smaller. (An image moves
upward.)
-: Leading edge margin becomes larger. (An image moves
downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit mm
Default value 0
REG-DUP2 Rgst start timing adj: Heavy, 2nd side
Lv.1 Details To adjust the leading edge margin by changing the timing to turn ON
the Registration Motor when feeding the second side of heavy paper.
As the value is incremented by 1, the margin on the leading edge of
paper is increased by 0.1 mm.
+: Leading edge margin becomes smaller. (An image moves
upward.)
-: Leading edge margin becomes larger. (An image moves
downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit mm
Default value 0
LP-FEED1 Cassette pre-rgst arch amount: Plain
Lv.1 Details To adjust the arch amount before registration when feeding plain
paper from the cassette.
As the value is incremented by 1, the pre-registration arch amount
changes by 0.5 mm.
+: Increase
-: Decrease
Use case To adjust the arch amount before registration when feeding plain
paper from the cassette.
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit mm
Default value 0
8
Service Mode > COPIER > ADJUST > FEED-ADJ
8 Service Mode > COPIER > ADJUST > FEED-ADJ
COPIER > ADJUST > FEED-ADJ
LP-MULT1 MP Tray pre-rgst arch amount: Plain
Lv.1 Details To adjust the arch amount before registration when feeding plain
paper from the Multi-purpose Tray.
As the value is incremented by 1, the pre-registration arch amount
changes by 0.5 mm.
+: Increase
-: Decrease
Use case To adjust the arch amount before registration when feeding plain
paper from the cassette.
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit mm
Default value 0
LP-DUP1 Duplex pre-rgst arch amount: Plain
Lv.1 Details To adjust the arch amount before registration when feeding plain
paper in duplex mode.
As the value is incremented by 1, the pre-registration arch amount
changes by 0.5 mm.
+: Increase
-: Decrease
Use case To adjust the arch amount before registration when feeding plain
paper from the cassette.
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit mm
Default value 0
REG-SPD Speed adjustment of Registration Motor
Lv.1 Details To adjust 1/1 speed of the Registration Motor.
As the value is incremented by 1, the speed is increased by 0.2%.
+: The speed is increased.
-: The speed is decreased.
As the value is reduced, blur image around 40 to 45 mm of the
trailing edge is alleviated.
Use case When blue image occurs around 40 to 45 mm of the trailing edge
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -5 to 5
Unit %
Default value 0
8-123
T-8-33
8-123