Canon imageRUNNER ADVANCE C5255 Series Service Manual page 1007

COPIER > OPTION > IMG-FIX
FXS-TMP7 ITOP control temperature: Plain paper 2
Lv.1 Details To set the offset of ITOP control temperature for plain paper 2 (82 to
105 g/m2).
As the value is incremented by 1, the control temperature is increased
by 5 deg C from the specified value.
Use case When uneven gloss occurs on the leading edge (94mm) of plain paper
2
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit deg C
Default value 0
FXS-TMP8 ITOP control temperature: Transparency
Lv.1 Details To set the offset of ITOP control temperature for transparency.
As the value is incremented by 1, the control temperature is increased
by 5 deg C from the specified value.
Use case When uneven gloss occurs on the leading edge (94mm) of
transparency
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit deg C
Default value 0
FXS-TM10 ITOP control temperature: Coated paper 2
Lv.1 Details To set the offset of ITOP control temperature for coated paper 2 (164
to 220 g/m2).
As the value is incremented by 1, the control temperature is increased
by 5 deg C from the specified value.
Use case When uneven gloss occurs on the leading edge (94mm) of coated
paper 2
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit deg C
Default value 0
8
Service Mode > COPIER > OPTION > IMG-FIX
8 Service Mode > COPIER > OPTION > IMG-FIX
COPIER > OPTION > IMG-FIX
FXS-TMP9 ITOP control temperature: Coated paper 1
Lv.1 Details To set the offset of ITOP control temperature for coated paper 1 (106
to 163 g/m2).
As the value is incremented by 1, the control temperature is increased
by 5 deg C from the specified value.
Use case When uneven gloss occurs on the leading edge (94mm) of coated
paper 1
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit deg C
Default value 0
THIN-LP Set of fixing arch ctrl with thin paper
Lv.2 Details To set the arch control method between the secondary transfer and
fixing when feeding thin paper (52 g/m2).
Normally, the arch control is executed at the point where arch on the
trailing edge of paper is small.
When 1 is set in the case that an image failure (crepe mark) occurs
with thin paper, the control is always executed at the point where the
arch on a paper is large while feeding thin paper.
Use case When an image failure (crepe mark) occurs with thin paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Arch control at the point where arch is small, 1: Arch control to make
the arch large with thin paper
Default value 1
TMP-TB11 Fixing control temperature:Recycled ppr
Lv.1 Details To set the offset of fixing control temperature for recycled paper (52 to
105 g/m2).
As the value is incremented by 1, the control temperature is increased
by 5 deg C.
Increase the value when a fixing failure occurs, and decrease the
value when fixing offset occurs.
Use case When offset/fixing failure occurs on recycled paper
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range - 3 to 2
-3: -15 deg C, -2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2:
+10 deg C
Unit deg C
Default value 0
8-187
8-187