Canon imageRUNNER ADVANCE C5255 Series Service Manual page 973

Hide thumbs Also See for imageRUNNER ADVANCE C5255 Series:
Table of Contents

Advertisement

COPIER > OPTION > FNC-SW
UNLMTBND
Over 400 binders print job support set
Lv.1 Details
To set whether to support print job that exceeds 400 binders.
With the setting to support, the machine makes prints by sharing
binders according to job attribution.
Select "1: Not supported" if the user does not print job* with large
quantity of binders.
Use case
When supporting print job that exceeds 400 binders
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 1
0: Automatic setting (When the print server is not connected: not
supported; When the print server is connected: supported)
1: Not supported
Default value
0
MIBCOUNT
Scope range set of Charge Counter MIB
Lv.2 Details
To set the range of counter information that can be obtained as MIB
(Management Information Base).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 2
0: All charge counters are obtained, 1: Only the displayed counter* is
obtained, 2: All charge counters are not obtained
*: Counter specified by the following: COPIER> OPTION> USER>
COUNTER 1 to 6
Default value
0
Related service mode
COPIER> OPTION> USER> COUNTER1 to 6
MEAP-PRI
Setting of MEAP task priority
Lv.2 Details
Selecting "1: ON" increases MEAP task priority.
Use case
When improving processing performance of MEAP
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
1
CNTR-SW
Init of parts counter estimated life value
Lv.1 Details
To return the estimated life value of parts counter to the initial value.
Use case
Upon user's request
Adj/set/operate method 1) Enter 0, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0: Returned to the initial value
Default value
0
8
Service Mode > COPIER > OPTION > FNC-SW
8
Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
W/RAID
Set of HDD Mirroring Kit installation
Lv.1 Details
To set installation state of HDD Mirroring Kit.
Select "1: Installed" when installing the HDD Mirroring Kit. Select "0:
Not installed" when removing the HDD Mirroring Kit.
Use case
When installing/removing HDD Mirroring Kit
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 1
0: Not installed, 1: Installed
Default value
0
PSWD-SW
Password type set to enter service mode
Lv.1 Details
To set the type of password that is required to enter when getting into
service mode.
2 types are available: one for "service technician" and the other for
"system administrator + service technician".
When selecting the type for "system administrator + service
technician", enter the password for service technician after the
password entry by the user's system administrator.
Use case
Upon request from the user who concerns security
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 2
0: No password, 1: Service technician, 2: System administrator +
service technician
Default value
0
SM-PSWD
Password setting for service technician
Lv.2 Details
To set password for service technician that is used when getting into
service mode.
Use case
When password is required to get into service mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
Be sure to select 1 or 2 for PSWD-SW in advance.
Display/adj/set range
1 to 99999999
Default value
11111111
Related service mode
COPIER> OPTION> FNC-SW> PSWD-SW
RPT2SIDE
Set of report 1-sided/2-sided output
Lv.1 Details
To set whether to use 1-sided or 2-sided for report output of service
mode.
Use case
When making 2-sided report output to reduce the number of output
pages
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range
0 to 1
0: 1-sided, 1: 2-sided
Default value
1
Related service mode
COPIER> FUNCTION> MISC-P> P-PRINT
8-153
8-153

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents