Hdd - Canon imageRUNNER ADVANCE C5255 Series Service Manual

5
Adjustment > Main Controller > HDD
Main Controller

HDD

How to Replace Refer to "Removing the HDD".
the Parts
Before 1) Back up the Settings/Registration data.
Replacing Use the Remote UI.The data can be collectively saved in a DCM file format using
the steps below.
Settings/Registration > Management Settings > Data Management > Import/
Export All > Export
Target data:
• Settings/Registration Basic Information
• Paper Type Management Settings
• Forwarding Settings
• Box Settings
• Department ID Management Settings
• Main Menu Settings
• Web Access Settings
• Favorite Settings
• Address Book
• User Access Control for Advanced Box
• Quick Menu Settings
• MEAP Application Setting Information
• User Setting Information
• Service Mode Settings (hidden by default)
* It can be displayed by selecting "1" in service mode (Lv1) > Option > USER >
SMD-EXPT. Printing out the Settings/Registration data becomes unnecessary by
saving the service mode setting values.
Select "Select All" for the items to export, enter the encryption password, and then
select "Select Exporting".
5 Adjustment > Main Controller > HDD
Aftter 1) Format the HDD.
Replacement 1-1) Start the machine in safe mode (turn ON the main power switch while
simultaneously pressing 2+8 keys).
1-2) Execute Formatting All Partitions using SST.
2) Download the system software
2-1) Download the system software (system/LANG/RUI, etc.) using SST.
3) Initialize the key/certificate/CA certificate.
(Lv.2) COPIER > FUNCTION > CLEAR > CA-KEY
4)Turn OFF and then ON the power
5) Restore the backup data.
Use the Remote UI. Follow the steps below to specify the DCM file stored earlier.
Settings/Registration > Management Settings > Data Management > Import/
Export All > Import
Enter the encryption password entered at exporting, and select "Start Importing".
Turn OFF and then ON the power after importing.
6) When an encryption key/certificate/CA certificate has been generated or added
by the user, ask the user to execute regeneration.
7) Execute auto gradation adjustment (full adjust). Settings/Registration mode:
Adjustment/Maintenance > Adjust Image Quality > Auto Adjust Gradation
When using 1) Go to COPIER > FUNCTION> INSTALL > CARD and enter the numerical value
the Card of the leading card which is used for Department ID.
Reader and Then, press "OK" button. (e.g.: If No.1 to No.1000 cards are used for
imageWARE Department ID, enter "1" of the leading card.)
Accounting 2) After turning OFF and ON the main power switch, perform the following
Manager operations from Settings/Registration mode.
• In Management Settings > User Management > Department ID Management >
Page Totals, be sure that "ID00000001" to "ID00001000" are created.
• Set the following: Preferences > Network > TCP / IP Settings > IPv4 Settings>IP
Address Settings > IP Address, Gateway Address, Subnet Mask
• In Management Settings > User Management> System Manager Information
Settings> System Manager ID and System PIN, register any number for them.
Then, turn OFF and ON the main power switch.
If "System Manager ID" and "System PIN" are not registered, "card registration
to device" cannot be executed for the imageWARE Accounting Manager setting
operation.
3) Download the card ID from imageWARE Accounting Manager to the Main Body
again.
4) After downloading is completed, go to Management Settings > User
Management > Department ID Management > Page Totals. Be sure that only
the downloaded card ID is displayed.
5) Print using the user card registered from imageWARE Accounting Manager.
Be sure that the card information used for the target devices of imageWARE
Accounting Manager is collected.
Points to Note when Using the System Software-installed HDD When using the
HDD which was installed the system software of the other machine (different serial
number), be sure to format the HDD after the installation.
If the HDD is not formatted, the operation cannot be guaranteed.
5-2
5-2