Canon imageRUNNER ADVANCE C5255 Series Service Manual page 1068

OPTION
SORTER > OPTION
BLNK-SW Set fold pstn margin width: Saddle Fin
Lv.1 Details To set the margin width of fold position on Saddle Finisher.
Use case When changing the margin width of fold position
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal, 1: Wider
Default value 0
BUFF-SW ON/OFF of buffer operation: Finisher-C1
Lv.1 Details To set ON/OFF of buffer operation in the Finisher.
When misalignment occurs, set 1.
When 1 is set, alignment performance is improved, but productivity
decreases.
Use case When misalignment of paper stack occurs (misalignment of 3 sheets
at the lowest part of the stack in case of the side stitch, and 3 sheets
at the middle of the stack in case of saddle stitch)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When the buffer operation is set to OFF, productivity decreases.
Display/adj/set range 0 to 1
0: OFF (Performing buffer operation), 1: ON (Not performing buffer
operation)
Default value 0
PRCS-SP1 Set buffer stack Fd SPD to Process Tray
Lv.1 Details To set the speed to feed the buffered paper stack to the Process
Tray Stopper in collate/staple mode.
When 1 is set, the feeding speed becomes fast, so misalignment due
to paper return failure is alleviated.
Use case When misalignment due to paper return failure occurs in collate/
staple mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: 600 mm/s, 1: 700 mm/s
Default value 1
8
Service Mode > SORTER > OPTION
8 Service Mode > SORTER > OPTION
SORTER > OPTION
STCR-DWN Set occasional misalign prev mode: Fin
Lv.1 Details To set ON/OFF of occasional misalignment prevention mode.
When misalignment in feed direction occurs at approx. every 30
sheets for thin/plain paper (105g/m2 and less), set 1.
Use case When misalignment in feed direction occurs for thin/plain paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
PRCS-SP3 Set non-buffer stack Fd SPD to Proc Tray
Lv.1 Details To set the speed to feed the non-buffered paper stack to the Process
Tray Stopper in staple mode for thin/plain paper.
As the value is incremented by 1, the feeding speed is decelerated
by 50 mm/sec.
Use case When misalignment due to too much paper return (buckling on the
trailing edge) occurs in staple mode for thin/plain paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 8
0: 700 mm/s, 1: 650 mm/s, 2: 600 mm/s, 3: 550 mm/s, 4: 500 mm/s,
5 to 8: 450 mm/s
Default value 0
NSRT-STC Set poor stack prev mode at non-collate
Lv.1 Details When the stackability at non-sort delivery is low.
With this setting, the stacking performance at non-sort delivery is
improved.
Use case When the stackability at non-collating is low
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2
0: Paper is delivered to the Stack Tray in non-sort mode.
1: Deliver 2-sided printed paper via the Processing Tray in non-sort
mode.
2: Deliver 1-sided/2-sided printed paper via the Processing Tray in
non-sort mode.
Default value 1
8-248
8-248