Advertisement
●The Enter key flashes in red during charging.
End any calls or communications immediately.
Disconnect the optional AC adapter (Desktop holder) or
DC adapter from FOMA terminal. Then connect all the
devices correctly and start over. ☛P42, P43
If the problem still persists, contact "Repairs" listed on the
back of this manual.
Phone
●"Please wait for a while" is displayed and
does not go out.
･
･
You can call the number 110,119 and 118. However the
call may not be connected depending on the status.
●Calls cannot be made using the dial keys.
･
Have you set All Lock? ☛P158
･
Have you set Keypad Dial Lock? ☛P161
Have you set Self Mode? ☛P160
･
Have you set Omakase Lock (Remote Lock)? ☛P159
･
圏外
●
(outside service area) is indicated on the
display and you hear busy signals.
Are you outside the service area or in an area with poor
signal strength? ☛P45
●After dialing a number, you hear busy signals
and cannot establish your call.
･
Have you dialed the area code? ☛P50
･
Did you hear the dial tone before entering a phone
number?
indicated? ☛P45
･
圏外
Is
●The ring alert does not sound.
･
Is the ring alert volume set to silent? ☛P68
･
Is the following function set?
・Reject/Accept Call ☛P165
・Anonymous Caller ☛P166
・Mute Ring Time Setting ☛P167
・Reject non-Reg. Caller ☛P168
Have you set Silent Mode? ☛P135
･
･
Have you set Public mode (Driving mode)? ☛P73
･
Have you set All Lock? ☛P158
･
Have you set Self Mode? ☛P160
･
Is the ringing time for Voice Mail Service or Call
Forwarding Service set to 0 sec? ☛P392, P394
●An incoming voice call cannot be responded
with the Any Key Answer function.
Is Any Key Answer set to OFF? ☛P65
●During a voice call, the other party's voice is
hard to listen or too loud.
Has the earpiece volume setting been changed? Adjust it
appropriately. ☛P68
The voice line/Packet
communication equipment is
damaged or the voice line
network/Packet communication
network is so congested.
Please retry later. The
message can be deleted by
pressing a dial key.
●The redial data/received call history is erased
unexpectedly.
･
Is Keypad Dial Lock set on? ☛P161
･
Is PIM Lock set on? ☛P160
●When there is an incoming call, a name
recorded in the phonebook is not displayed or
the ring alert registered in the phonebook is
not generated.
･
Is the phone number notified by the other party? ☛P63
･
Does the phone number of the other party match the
phone number registered in the phonebook?
･
Is more than one phone number registered in the same
FOMA terminal phonebook or is the same phone
number registered in the FOMA terminal phonebook
and the UIM phonebook? ☛P107
･
Is Privacy Mode activated? ☛P162
●When there is an incoming call, a ring alert
not set sounds.
･
The ring alert set in multiple functions sounds depending
on the priority levels given below:
aIncoming settings of Multi Number
bAlert by Contact of the FOMA terminal phonebook
cAlert/Image by Group of the FOMA terminal phonebook
dSound Setting
Is Privacy Mode activated? ☛P162
･
●When there is an incoming call, an image not
set appears.
･
When video/i-motion containing sound and image is set
as ring alert for Call Alert, the set video/i-motion is used
as the image.
･
When call images are set in multiple functions, the
image appears depending on the priority levels given
below. For details ☛P143
aIncoming settings of Multi Number
bThe setting of the FOMA terminal phonebook Alert by
Contact of the FOMA terminal phonebook
cAlert/Image by Group of the FOMA terminal phonebook
dMail/Call Image (Call Alert/Videophone Alert) or
Sound Setting
Is Privacy Mode activated? ☛P162
･
●When there is an incoming call, the Enter key
lights/flashes in a lighting pattern and lighting
color not set.
･
If a lighting pattern or lighting color is set for multiple
functions, the Enter key lights/flashes depending on the
priority levels given below:
aAlert by Contact of the FOMA terminal phonebook
bAlert/Image by Group of the FOMA terminal phonebook
cLight Alert Setting
Is Privacy Mode activated? ☛P162
･
Settings and operations
●Key icon is displayed instead of menu icon
and icon cannot be selected.
In case some functions cannot be activated because of
various lock functions or the UIM not inserted, their icons
change to
and cannot be selected.
Next
447
Advertisement
Chapters
