Advertisement
2
Select Direct input
(the other party's phone number)
･
To send to a party that uses an overseas
carrier other than DoCoMo, enter "+" (by
holding down 0 for over a second) and the
country code plus the party's mobile phone
number. Omit the first 0 of the phone number.
You can also send by entering "010" and the
country code plus the party's mobile phone
number (add "010" when replying to a received
SMS message from overseas).
･
You can enter up to 26 characters in the
field. However, up to 20 characters (21
characters if "+" is contained) can be sent as
address.
■
Searching the phonebook: Select View
z
phonebook
Select the party
･
When multiple phone numbers are
registered, select a phone number.
z
3
Select
Enter the message
･
When the font type is set to Japanese in SMS
Setting, up to 70 one-byte or two-byte
characters can be entered. A space is also
counted as a character in the message.
･
When the font type is set to English in SMS
Setting, up to 160 one-byte characters can be
entered. Alphanumerics and symbols (except
for ｀｡｢｣､･ﾞ and ﾟ) can be sent. A one-byte
space is counted as a character in the
message.
･
Line feeds can be inserted in the message.
Press # to enter a line feed in 5-touch Input
Method (except in the one-byte and two-byte
numeric modes). A line feed is counted as a
character in the message. However, it is
replaced by a one-byte space on the receiver's
terminal.
Inserting a signature: m45
■
･
Signature must be registered beforehand.
Press p
4
Saving without sending: m2
■
･
If neither the address nor message is
entered, the SMS cannot be saved.
･
You can edit and send the unsent SMS.
☛P239
z
Enter the address
INFORMATION
Depending on signal conditions, characters may not be
●
displayed correctly at the receiver side.
Even if Not notify is set in Caller ID Notification, the caller
●
ID is sent to the receiver when SMS is sent.
If you enter some symbols (
●
font type is English, the number of characters that can be
sent is reduced. In this case, you may not be able to
send the message even if the number of characters is
less than the limit. In this case, reduce the number of
characters and send it again.
When there is not enough available storage space, or the
●
maximum number of saved items is exceeded, SMS
cannot be composed. Delete unnecessary i-mode Mail
and/or SMS from Unsent messages. ☛P252
Even when SMS has been sent, a model incompatible
●
with SMS reception cannot receive SMS normally.
The font type and whether to receive the delivered report
●
must be set in SMS Setting beforehand. You can also
change the settings for the delivered report and storage
period in the SMS Center while composing SMS.
When transmission is completed correctly, SMS is saved
●
in the Outbox folder of Outbox. However, when the sent
SMS matches the criteria specified in Sort Criteria, it is
saved in the specified folder. When there is not enough
available storage space, or the maximum number of
saved items is exceeded, the oldest sent mail is
overwritten. Be sure to protect sent mail you want to
keep.
When transmission fails, an error message appears and
●
SMS is saved in the Unsent messages folder of Unsent
messages. You can edit and send the SMS from the
Unsent messages folder. ☛P239
When you set the delivered report to Request and send
●
SMS, you will receive a delivered report that notifies you
that the message has been received by the other party's
FOMA terminal. The delivered report is saved in Inbox.
When SMS is received
When there is incoming SMS, it is automatically
received and you are informed by the screen
display, ring alert, vibrator, and/or the Enter key.
The received SMS is saved in Inbox.
･
Maximum number of items that can be saved
☛P38
｜＾{ } [ ] ˜
and ￥) when the
Receive SMS
Next
265
Advertisement
Chapters
