Advertisement
Repeat：
Set the condition for repetitive automatic
starting of i-
ppli.
α
･
When OneTime is set, set the date for auto
starting in Date field.
･
When Daily is set, i-
automatically at the time set in Time field
every day.
･
When Weekly is set, set the day of week
for auto starting in Weekly field.
Weekly：
Set the day of week for auto starting when
Weekly is set for Repeat.
Date：
Set the date for auto starting when OneTime
is set for Repeat.
Software：
Specify whether to automatically start at the
intervals preset for i-
ppli 1 to 4：
i
- α
Depending on i-
of Auto Start can be set while it is operated.
Specify whether to enable the settings.
Press p
4
INFORMATION
Even when auto starting is set, i-
●
time of activation arrives in one of the following
situations. If i-
ppli is not started for the following
α
reasons (except for the ones marked with *1),
indicated on the standby display and the name of i-
the date and time and the reason for the start failure are
recorded in Start Failure History.
･
When FOMA terminal power is off*
･
When UIM operation is restricted (except for
pre-installed i-
ppli)
α
･
When UIM cannot be detected
･
When Auto Start is set to OFF*
･
The interval of auto start is too short
･
During a call, communication, or a PushTalk call
･
When a screen other than the standby display is
displayed or i-
ppli standby display operation is in
α
progress
･
When any other function is being used (excluding the
list display and edition of My Picture, the list display,
replay, and edition of i-motion, the list display and
replay of melody, or the list display and replay of Music
Player)
･
In All Lock, PIM Lock or Omakase Lock (Remote Lock)
･
When Privacy Mode is on (while Authorized access is
set to i-
α
ppli)
･
While an alarm clock or schedule alarm is sounding
(including when the set time is the same as the time
for Auto Start)
･
While Timer is in operation
･
When i-
ppli usage is stopped by the IP
α
ppli starts
α
ppli.
α
ppli DX, up to 4 conditions
α
ppli is not started if the
α
is
ppli,
α
1
1
When two or more i-
ppli applications are specified to
●
α
start automatically at the same time, only one i-
activated. The failed i-
ppli information is recorded in
α
Start Failure History, but
standby display.
In the User settings, the same setting set for other i-
●
cannot be set.
If all of the start time are set before the time set in Date
●
and Time Setting, auto starting will be disabled.
Displaying history when Auto Start of i-
fails
If automatic start of i-
ppli fails,
α
standby display and the i-
time and the failure reason are registered.
･
Up to 20 start failures are recorded. When there
are more than 20 abnormal exits, the 21st exit is
written over the oldest one.
･
When you display the start failure history or when
the next automatic start is successful,
standby display disappears.
Press m331
1
Deleting the history: p
■
Starting i-
ppli from a site or mail
α
Select a link item that can start the site or i-
of the site or i-mode Mail and then start the i-
(i-
ppli To).
α
1
Select a link item enabled to start i-
from the site or i-mode Mail
2
Select Yes
The connection to the site is terminated and
i-
ppli is started.
α
INFORMATION
If the i-
ppli you attempt to start with i-
●
α
saved in FOMA terminal, the message that there is no
specified i-
ppli is displayed and i-
α
started. Note that some i-
downloaded from sites even if it is not saved.
･
For i-
ppli that starts just after downloaded from a
α
site, a confirmation screen may be displayed asking
whether to make communication while it is activated.
･
When you quit i-
ppli started just after downloaded
α
from sites, a confirmation screen is displayed asking
whether to save i-
ppli. Note that some i-
α
not be able to be saved in FOMA terminal.
ppli is
α
is not displayed on the
ppli
α
ppli
α
Start Failure History
appears on the
ppli name, the date and
α
on the
z
Select Yes
i-
ppli To
α
ppli
α
ppli
α
ppli
α
ppli To is not
α
ppli cannot be
α
ppli may start just after
α
ppli may
α
Next
283
Advertisement
Chapters
