Advertisement
INFORMATION
If the IC card is not recognized when you hold the FeliCa
●
mark over the reader/writer, try again by changing the
position, angle, etc.
Do not expose FOMA terminal to strong shocks when
●
holding the FeliCa mark over the reader/writer.
The IC card can be used during a call or i-mode
●
connection by holding the FeliCa mark over the reader/
writer. However, you cannot start Osaifu-Keitai
compatible i-
ppli during i-mode connection.
α
The IC card can be used by holding the FeliCa mark over
●
the reader/writer even when the power is off, but not
when the battery pack is removed. When you use an IC
card function, attach the battery pack. Even when the
battery pack is attached, if it is not used for an extended
period or is not charged after a low battery alert, the IC
card may not be used. In this case, charge the battery.
When the power is off, you cannot start Osaifu-Keitai
●
compatible i-
ppli to read and write data in the IC card.
α
You cannot obtain ToruCa either.
i-
ppli may start when you hold the FeliCa mark over the
●
α
reader/writer. However, no i-
i-
ppli is not saved or is set not to start with i-
α
Starting Osaifu-Keitai compatible i-
m641
1
2
Select Osaifu-Keitai compatible i-
･
Osaifu-Keitai compatible i-
started, deleted and its folders managed in the
same way as normal i-
Meaning of the marks ☛P273
･
■
Quitting:
Quit the Osaifu-Keitai compatible i-
using the procedure specified for each.
You can also quit by pressing f and
･
selecting Yes.
ppli starts when the target
α
ppli To.
α
ppli
α
ppli
α
ppli can be auto
α
ppli.
α
ppli
α
INFORMATION
While Osaifu-Keitai compatible i-
●
card may not be used by holding the FeliCa mark over a
reader/writer.
Some of Osaifu-Keitai compatible i-
●
not be available during a videophone call.
When any of the following conditions occurs, Osaifu-
●
Keitai compatible i-
ppli under operation and reading
α
and writing data in the IC card are interrupted. In that
case, the data may be discarded:
･
When there is an incoming call (except when the
ringing time for Voice Mail Service and Call Forwarding
Service is set to 0 sec)
･
When a PushTalk call arrives (excluding the case
where i-mode preferred is set in i-mode Arrival Act: PT
and call arrives while communicating)
･
After the specified time by Timer has elapsed
･
When the date and time set in Alarm Clock or
Scheduler arrives
･
When you switch to another function
When you press b during a call or alarm sounding to
●
switch to the Osaifu-Keitai compatible i-
operation varies for each Osaifu-Keitai compatible
service that you subscribe to.
Some functions of Osaifu-Keitai compatible i-
●
not start or operate correctly when your terminal is
outside the service area or cannot use the saved data.
What's ToruCa?
ToruCa is an electronic card that is available
through Osaifu-Keitai, which can be used as a
flyer, restaurant card, coupon, etc.
You can obtain ToruCa from the reader/writer and
sites and exchange the obtained ToruCa easily
by using mail, infrared communication, and
miniSD memory card.
The obtained ToruCa is saved in ToruCa in the
LifeKit menu.
･
Supporting models: 902i series, 902iS series and
F702iD
For details, see "i-mode User's Manual".
ppli is started, the IC
α
ppli operations may
α
ppli screen, the
α
ppli may
α
Next
295
Advertisement
Chapters
