If the specified i-
ppli is set not to start with i-
●
α
message is displayed and i-
Operating the i-
ppli standby display
α
When i-
ppli is set for the standby display, you
α
can start i-
ppli from the standby display to
α
operate. On the i-
ppli standby display
α
is indicated at the top of the screen.
・
It is necessary to set i-
display beforehand. ☛P139
INFORMATION
When you set i-
ppli that performs communication, it
●
α
may not operate correctly depending on radio wave
conditions, etc.
While All Lock, PIM Lock, Privacy Mode (i-
●
Authorized access) or Omakase Lock (Remote Lock) is
active, the i-
ppli standby display will be canceled
α
temporarily. If you cancel All Lock, PIM Lock, or Privacy
Mode, the i-
ppli standby display restarts.
α
If the use of i-
ppli set to the i-
●
α
stopped by IP, the i-
ppli standby display is canceled.
α
While the i-
ppli standby display is activated, if an error
●
α
that makes it difficult to continue the i-
display occurs, a confirmation screen appears asking
whether you will cancel or not. When you select Yes, the
i-
ppli standby display setting is canceled. At this time,
α
the name of i-
ppli and end date/time are recorded in
α
Abnormal Exit History.
You cannot connect to a site (Web To) from the i-
●
standby display.
When FOMA terminal is turned on with the i-
●
standby display set, a confirmation screen is displayed
asking whether to start the i-
you select Yes, the i-
ppli standby display starts. When
α
you select No, the i-
ppli standby display setting is
α
canceled. If you operate nothing within 5 seconds after
the confirmation screen appeared, the i-
display starts automatically. When the power is turned on
by Auto Power ON, the i-
α
automatically starts, without displaying the confirmation
screen.
Starting i-
ppli of the i-
α
Press c in the i-
1
The screen is changed to the i-
or
blinks at the top of the display.
Note: The miniSD memory card is not included in the bundle and needs to be purchased. ☛P331
284
ppli To, a
α
ppli is not started. ☛P274
α
i-
ppli Standby Display
α
or
ppli for the standby
α
ppli is set to
α
ppli standby display is
α
ppli standby
α
ppli
α
ppli
α
ppli standby display. When
α
ppli standby
α
ppli standby display
ppli standby display
α
ppli standby display
α
ppli screen and
α
Quitting i-
ppli to return to the i-
α
display
f while i-
1
ppli is running
α
End
i-
ppli is ended and the i-
α
activated. The icon at the top of the display
switches from
to
・
The procedure to quit i-
i-
ppli standby display depends on the type of
α
ppli. c makes some types of i-
i-
α
return.
・
Even if End is selected, the i-
display setting is not canceled. To cancel,
select Cancel.
display disappear.
INFORMATION
You can also cancel i-
ppli by highlighting i-
●
α
ppli standby display in the software list, pressing m,
i-
α
selecting i-
ppli display and then selecting Cancel.
α
Displaying the exit history of i-
display
When an error that makes it difficult to continue the
i-
ppli standby display occurs, the name of i-
α
date and time are recorded.
・
Up to 20 abnormal exits are recorded. When
there are more than 20 abnormal exits, the 21st
exit is written over the oldest one.
・
In the normal end, exits are not registered.
Press m332
1
Deleting the history: p
■
Managing i-
ppli
α
Upgrading i-
ppli
α
When i-
ppli has been updated, it can be upgraded.
α
・
i-
ppli whose usage is stopped by IP cannot be
α
upgraded.
d (for over a second)
1
z
2
Highlight i-
ppli
α
・
When upgrade is unnecessary, the message
that i-
ppli is the newest is displayed.
α
ppli standby
α
z
Select
ppli standby display is
α
, or from
to
.
ppli and return to the
α
ppli
α
ppli standby
α
and
at the top of the
ppli of the
α
ppli standby
α
Abnormal Exit History
ppli,
α
z
Select Yes
Upgrade
z
Select a folder
m5
z
Select Yes