Advertisement
Starting i-
ppli
α
d (for over a second)
1
■
Displaying only the IC card software
(Osaifu-Keitai compatible i-
m641
The IC card software list screen is displayed.
Go to Step 3.
2
Select a folder
The software list is displayed.
: No i-
ppli
α
3
Select an i-
ppli application to start
α
ab c
d
e
f
Software list screen
a
：Normal i-
ppli
α
：i-
ppli DX
α
：Message i-
ppli
α
b
：i-
ppli that can be set for i-
α
display
：i-
ppli that is set for i-
α
display
c
：i-
ppli with Auto Start
α
：i-
ppli at stopped condition by IP
α
d
to
:
i-
ppli registered in Two-key Shortcut
α
e
：Protected i-
ppli
α
：i-
ppli downloaded from SSL pages
α
：Protected i-
ppli which was downloaded
α
from SSL pages
f
：i-
ppli registered in One-key Shortcut
α
：Unavailable because of the UIM operation
restriction
g
：Osaifu-Keitai compatible i-
･
When Confirm every session is set for NW
transmission of i-
ppli to be started, a
α
confirmation screen is displayed asking
whether to connect.
Menu 31
ppli):
α
: i-
ppli present
α
c
g
f
d
IC card software list screen
ppli standby
α
ppli standby
α
ppli
α
Quitting i-
ppli
α
Quit i-
ppli in the procedure specified for each.
α
･
You can also quit i-
α
selecting Yes.
INFORMATION
i-
ppli is interrupted in the following cases. When you
●
α
quit the function being used and running, i-
resumed. To resume i-
ppli without quitting the current
α
function, press b and select i-
may not be resumed by b depending on the function
running. Some i-
ppli may not return to the state before
α
interruption when resumed.
･
When there is an incoming call (except when the
ringing time of Voice Mail Service and Call Forwarding
Service is set to 0 Sec.)
･
When a PushTalk call arrives (excluding the case
where i-mode preferred is set in i-mode arv. act:PT and
a PushTalk call arrives during i-
･
When the time set by Timer has passed
･
When the time set in the schedule alarm or Alarm
Clock has come
･
When you switch to another function
When you are outside the service area or the saved data
●
cannot be used, i-
ppli may not start or not operate
α
correctly.
Images used on i-
ppli or your entered data may
●
α
automatically be sent to the server via Internet. Images
used on i-
ppli are images shot with the camera while
α
i-
ppli is activated, images obtained using the i-
α
infrared communication function, images downloaded by
i-
ppli from i-mode or Internet websites, or images
α
obtained by i-
ppli from Data Box.
α
For some i-
ppli, the IP can access i-
●
α
mobile phone and directly stop its use. In this case,
starting, setting for standby or upgrading of the i-
cannot be performed and only deleting and displaying
the detailed information can be performed. To use again,
please contact the IP to release suspension of i-
For some i-
ppli, the IP may send data to i-
●
α
in the mobile phone.
When the IP requests to stop/restart i-
●
to i-
ppli, FOMA terminal communicates and
α
this case, the communication charge is not required.
Some software allows data to be saved on the miniSD
●
memory card. Show the detail information to see whether
or not the miniSD memory card is used. The data saved
on the miniSD memory card may not be used by other
FOMA models.
The i-
ppli continues its operation even if you set Key
●
α
Lock and the display indication disappears while i-
is operating.
Because of the 3D polygon*
●
dimensional image can be displayed with i-
*1 By combining polygons (triangles and squares), 3
dimensional image with depth can be displayed.
ppli by pressing f and
ppli is
α
α
ppli. However, i-
ppli
α
ppli communication)
α
ppli
α
ppli saved in the
α
ppli
α
ppli.
α
ppli saved
α
ppli or send data
α
blinks. In
ppli
α
1
engine loaded, 3
ppli.
α
Next
273
Advertisement
Chapters
