NTT docomo FOMA D703i User Manual page 432

Command
AT + CRC = [n]
Specifies whether to use result codes of "+CRING:type" for incoming calls.
n = 0: Does not use the result code of "+CRING:type". (default and when parameter omitted)
n = 1: Uses the result code of "+CRING:type". The example of codes are as follows:
*1, *2 ex. Enter
AT + CREG = [n]
Specifies whether to show the "inside/outside the service area" information.
n = 0: Does not show the information. (default and when parameter omitted)
n = 1: Shows the information.
If you enter "AT + CREG?", it shows the information in the format of " + CREG:n,stat".
*1, *2 ex. Enter
AT + GMI
Shows the manufacturer's name of FOMA terminal.
ex. Enter
AT + GMM
Shows FOMA terminal name.
ex. Enter
AT + GMR
Shows the version of FOMA terminal.
ex. Enter
AT + IFC = [n,[m]]
Specifies the local flow control between the PC and FOMA terminal.
n is for setting the DCE-by-DTE control.
m is for setting the DTE-by-DCE control. If you omit this parameter, the same value as n is assumed.
If you omit both parameters, "AT+IFC = 2, 2" is assumed.
*1, *2 ex. Enter
AT+WS46= [22] Specifies the radio network FOMA terminal uses to originate a call.
*1, *2 ex. Enter
ATA Specifies how to handle incoming packet or 64K data communications. For incoming packet
communications, you can specify the following:
ATA184: Receives an incoming call without the caller ID displayed
ATA186: Receives an incoming call with the caller ID displayed
ex. Enter
A/ Reexecutes the previous command.
ex. Enter
ATD Originates a packet or 64K data communication.
・ Packet communication: Enter "ATD ＊ 99 ＊＊＊ cid#". If you omit cid parameter, "cid = 1" is assumed.
・64K data communication: Enter it in the format of "ATD phone number".
・Redialing: Enter in the format of "ATDL" or "ATDN".
ex. Enter
ATE [n] Echoes back the characters sent from the PC.
n = 0: Gives no echo back. (when parameter omitted)
n = 1: Gives echo back. (default)
*1, *2 ex. Enter
ATH Disconnects communication.
ex. Enter
ATI [n] Shows the identification code.
n = 0: Shows "NTT DoCoMo". (when parameter omitted)
n = 1: Shows model name of FOMA terminal. n = 2: Shows the version of FOMA terminal.
ex. Enter
ATO Switches the mode from the online command to the online data.
ex. Enter
ATQ [n] Specifies whether to show the result code on the PC.
n = 0: Shows the result code. (default and when parameter omitted)
n = 1: Does not show the result code.
*1, *2 ex. Enter
ATV [n] Specifies whether to show the result with numeric codes or text messages.
n = 0: Shows the result with numeric codes. (when parameter omitted)
n = 1: Shows the result with text messages. (default)
*1, *2 ex. Enter
Packet communication... +CRING:GPRS "PPP",,,"mopera.net"
64K data communication... +CRING:SYNC
AT + CRC = 0
stat=0: Outside the service area stat = 1: Inside the service area (home) stat = 4: Unknown
stat = 5: Inside the service area (visitor)
AT + CREG = 0
AT + GMI
AT + GMM
AT + GMR
n = 0: Does not use the flow control. n=1: Uses XON/XOFF flow control.
n = 2: Uses RS/CS (RTS/CTS) flow control. (default)
m = 0: Does not use the flow control. m = 1: Uses XON/XOFF flow control.
m = 2: Uses RS/CS (RTS/CTS) flow control. (default)
AT + IFC = 2,2
AT + WS46 = 22
ATA
A/
When you enter it in the format starting with "ATD184 ＊ 99", 184 (hide caller ID) is attached to the call
outgoing to the APN specified with cid parameter (186 (show caller ID) is treated in the same manner).
ATD phone number
ATE0
ATH
ATI0
ATO
ATQ0
ATV1
Description & Parameter
AT + CRC?
Display
AT + CREG?
Display
Display None
Display None
Display None
AT + IFC?
Display
AT + WS46?
Display
Display None
Display None
Display None
Display None
Display None
Display None
Display None
Display None
Display None
27
AT + CRC = ?
Test
AT + CREG = ?
Test
AT + GMI = ?
Test
AT + GMM = ?
Test
AT + GMR = ?
Test
AT + IFC = ?
Test
AT + WS46 = ?
Test
Test None
Test None
Test None
Test None
Test None
Test None
Test None
Test None
Test None
Next