Starting I-Αppli From Sites Or Mails; I-Αppli To; Operating The I-Αppli Standby Display; I-Αppli Standby Display - NTT docomo FOMA D703i User Manual

･
When Auto Start is set to OFF*
･
When the interval of auto starting is too short
･
During a call or communication
･
When a screen other than the standby display is
displayed or i- ppli standby display operation is in
α
progress
･
When any other function is being used
･
In All Lock, PIM Lock or Omakase Lock (Remote Lock)
･
When Privacy Mode is on (with Authorized access set
for i-
α ppli)
･
While the alarm clock sound or schedule reminder is
sounding (including when the set time is the same as
the time for Auto Start)
･
While the timer is in operation
･
When i- ppli usage is stopped by the IP
α
If two or more i- ppli applications are specified to start
● α
automatically at the same time, only one application is
activated. The failed i- ppli information is recorded in
α
Start Failure History, but
standby display.
Displaying history when Auto Start of i-
fails
If auto start of i- ppli fails,
α
standby display and the i-
time and the failure reason are recorded.
･
Up to 20 start failures are recorded. When there
are more than 20 abnormal exits, the 21st exit is
written over the oldest one.
･
When you display the start failure history or when
the next auto start is successful,
standby display disappears.
Press m331
1
Deleting the history: p on the log
■
z
display screen
Starting i- ppli from sites or mails
α
Select a link item that can start i-
i-mode mails and then start the i-
To).
1
Select a link item enabled to start i-
from sites or i-mode mails
2
Select Yes
The connection to the site is terminated and
i- ppli is started.
α
1
is not displayed on the
ppli
α
Start Failure History
appears on the
ppli name, the date and
α
on the
Select Yes
i- ppli To
α
ppli of sites or
α
ppli (i- ppli
α α
ppli
α
INFORMATION
If the i- ppli you attempt to start with i-
● α
saved in FOMA terminal, i-
that some i- ppli may start just after downloaded from
α
sites even if it is not saved.
･
For i- ppli that starts just after downloaded from a
α
site, a confirmation screen may be displayed asking
whether to make communication while it is activated.
･
When you quit i- ppli started just after downloaded
α
from sites, a confirmation screen is displayed asking
whether to save i- ppli. Note that some i-
α
not be saved in FOMA terminal.
If the specified i- ppli is set not to start with i-
● α
message is displayed and i-
Operating the i- ppli standby display
α
When i- ppli is set for the standby display, you
α
can start i- ppli from the standby display to
α
operate. On the i- ppli standby display
α
is indicated at the top of the screen.
･
It is necessary to set i-
display beforehand. ☛P110
INFORMATION
When you set i- ppli that performs communication, it
● α
may not operate correctly depending on signal
conditions, etc.
While All Lock, PIM Lock, Privacy Mode (with i-
●
to Authorized access) or Omakase Lock is active, the
i- ppli standby display will be canceled temporarily. If
α
you cancel All Lock, PIM Lock, Omakase Lock, or
Privacy Mode, the i- ppli standby display restarts.
α
If the use of i- ppli set as the i-
● α
stopped by IP, the i- ppli standby display is canceled
α
next time you turn on your FOMA terminal.
While the i- ppli standby display is activated, if an error
● α
that makes it difficult to continue the i-
display occurs, a confirmation screen appears asking
whether you will cancel or not. When you select Yes, the
i- ppli standby display setting is canceled. At this time,
α
the name of i- ppli and end date and time are recorded
α
in Abnormal Exit History.
You cannot connect to a site (Web To) from the i-
●
standby display.
When FOMA terminal is turned on with the i-
●
display set, a confirmation screen is displayed asking
whether to start the i- ppli standby display. When you
α
select Yes, the i- ppli standby display starts. When you
α
select No, the i- ppli standby display setting is canceled.
α
If you operate nothing within 5 seconds after the
confirmation screen appeared, the i-
starts automatically. When the power is turned on by Auto
Power ON, the i- ppli standby display automatically
α
starts, without displaying the confirmation screen.
ppli To is not
α
ppli cannot be started. Note
α
ppli may
α
ppli To, a
α
ppli is not started. ☛P234
α
i- ppli Standby Display
α
or
ppli for the standby
α
ppli set
α
ppli standby display is
α
ppli standby
α
ppli
α
ppli standby
α
ppli standby display
α
i- ppli 239
α