NTT docomo FOMA D703i User Manual page 370

●Infrared
Connection interrupted.
An error occurred during infrared
communication. During infrared
communications, do not move
FOMA terminal pointed at the other
terminal's infrared data port before
data sending and receiving is
complete. ☛P273
●Infrared
Failed to connect via
authentication.
Sending all data was failed because
the authentication password is not
correct. Enter the same
authentication password between
sender and receiver.
●Infrared
No response. Retry data
exchange?
After entering into the infrared
communication state, 5 or more
seconds have elapsed with no other
terminals for communications found.
Point FOMA terminal at the other
terminal's infrared data port with a
distance of 20 cm or less and select
Yes. ☛P273
●Infrared
No UIM. Unable to start
requested software.
Because no UIM is inserted, the
specified i- ppli cannot be started
α
even when i- ppli To is set in the
α
data received by infrared
communications.
●Infrared
Unable to switch to data
transfer mode.
FOMA terminal is communicating.
Processes cannot be performed
because switching to data transfer
mode is unavailable. Terminate
communicating or retry again later.
●Input error (205)
Input data for i-mode sites or
websites contain error. Check the
input data for errors.
●Insufficient memory.
Operation is interrupted due to
insufficient memory.
●Insufficient memory. Unable
to edit signature. Delete
signature.
When editing the signature is
started, memory shortage occurs.
Delete the data of signature.
368 Appendix/Data Interchange/Troubleshooting
●Insufficient memory. Unable
to open window.
Windows cannot be opened
because the memory is insufficient.
Executing may be available by
closing the windows opened already
or terminating other running
functions.
●Invalid content. Change
i-motion type for replay.
Change now?
You tried to download a streaming
type i-motion file with the i-motion
type setting Normal type. Select Yes
to change the i-motion type setting.
Select No if you don't change the
setting. ☛P181
●Invalid content. Download
failed.
Cannot download because the
object contents to be charged are
invalid.
●Invalid data.
The downloaded data contains an
error.
●Syntax error. (XXX)
･
Dose not support the specified
i-mode sites or websites.
･
The URL may be incorrect. Make
sure that the URL is correct.
･
Unable to display because there is
an error in the received data.
･
Within service area, sending auto
send mail was unsuccessful.
●Invalid data. Connection
cannot be established. (400)
･
Cannot be connected because of
the error in i-mode sites or
websites. The URL may be
incorrect. Make sure that the URL
is correct.
･
Within service area, sending auto
send mail was unsuccessful.
●Invalid data. Failed to save.
Attached melodies or video/i-motion
files cannot be played because of
the incorrect data.
●Invalid data. Unable to save.
Data received through infrared
communications cannot be saved
because it is in a format
incompatible with FOMA terminal.
●Invalid data. Unable to save.
The downloaded data cannot be
saved because the data is invalid.
●Invalid File. (493)
Cannot be obtained due to an invalid
file.
●
Invalid UIM, incorrect display.
Cannot be displayed correctly
because of inserting a UIM different
from the one you were using when
you stored mail templates. Use the
same UIM as the one you were
using when downloading or saving.
●Invalid UIM, requested
service not available.
You tried to use data downloaded
from i-mode sites or websites or
saved from attachments of mail or
Message R/F with a UIM different
from the one you used when the
data was saved. Insert the same
UIM as used when those data were
downloaded to use it.
●Invalid UIM, requested
software failed to start.
The i- ppli to be used together with
α
the UIM used when downloading it
from a site, etc. cannot be started.
Insert the same UIM as used when the
software was downloaded to use it.
●Invalid URL.
The entered URL contains error.
Check the URL.
●Mails could not be sent to
following address. (561)
Sending i-mode Mail is failed for some
receivers. Pressing o displays the
receiver that the transmission failed.
Check to see if the address of the
receiver is correct and retry
transmission at another location with
good radio wave condition.
●Memory is full. Unable to
save.
FOMA terminal does not have
enough memory space and SMS
cannot be saved. Move SMS to UIM
or delete i-mode Mail or SMS.
●Memory shortage. Quit
application.
The running function is terminated
due to insufficient memory.
●Message kept in center.
SMS messages have already been
sent.
●Name too long. Saved with
incomplete name.
When registering an item selected
from the display of a site, etc. to the
phonebook, the number of characters
has exceeded the specified value.
Pressing o causes the phonebook
registration screen to be displayed,
with characters exceeding the limit
deleted for each item.