Setting The I-Αppli Standby Screen; Set I-Αppli Stand-By; Functions - NTT docomo FOMA SO706i Instruction Manual

Launching i-αppli from a site
When an i-αppli software launch specification is
displayed on an i-mode site, this setting allows the
software to be launched from the site.
This function cannot be used with some sites.
1 Sites screen (p.136) Select an item for
launching the software "YES"
N
Unlike ordinary i-αppli, some i-αppli software is
immediately launched from an i-mode site.
• These i-αppli are not stored on the FOMA terminal
after downloading from i-mode sites,
• Some i-αppli software cannot be stored on the
FOMA terminal.
Launching i-αppli from a mail
When an i-αppli software launch specification is
pasted into a received i-mode mail, this setting allows
the software to be launched from the i-mode mail.
Received mail detail screen (pp.170,
1
172) Select an item for launching the
software "YES"
N
The i-αppli launch specification cannot be quoted
even when you reply with a quote or forward the
i-mode mail. You cannot quote a launch specification
of an i-αppli by forwarding mail using the Infrared data
exchange function or DOCOMO keitai datalink
(p.329), etc.
Launching i-αppli from other

functions

You can launch an i-αppli from various functions such
as Infrared data exchange function, Bar code reader,
IC card function, ToruCa, data broadcast, etc.
■Infrared data exchange function
When the FOMA terminal received the i-αppli
launching signal while Infrared data exchange, i-αppli
software launches.
■Bar code reader
When the data scanned by the Bar code reader
contains an i-αppli software launch specification, you
can launch the software from the Bar code reader.
■IC card function
You can launch the software by holding the FeliCa
mark on the FOMA terminal over the reader/writer
unit.
198
■ToruCa
When an i-αppli software launch specification is
pasted into an acquired ToruCa, you can launch the
software from ToruCa.
■Data broadcast
When 1Seg data broadcast site contains i-αppli
activation specification, the software can be activated
from the site.
N
<IC card function>
The software is not launched in the following cases:
• When another function is running
• During calls
• When the software you want to launch cannot be
found
Setting the i-αppli Standby
Screen
You can set a selected i-αppli software as the standby
screen.
Some software applications cannot be set as the
standby screen.
Software list screen (p.187) o (Set)
1
"Stand-by display" "ON" o (Finish)
N
Only 1 i-αppli can be set as the i-αppli standby screen.
If software that communicates is set as the standby
screen, it may not run correctly when problems such
as poor signal quality occur.
If you select "OFF" for "Stand-by net" in "Software
setting", note that you may not be able to receive
timely information.
If "Dial lock" or "Original lock" is set or 2in1 is set to B
mode or Dual mode while the i-αppli standby screen is
displayed, the i-αppli standby screen ends. If "Dial
lock" or "Original lock" is released or 2in1 is set to A
mode, the i-αppli standby screen reappears.
When you switch tasks and display the standby
screen, the screen specified in "Stand-by display" of
"Display setting" appears even though the i-αppli
standby screen is set.
Activating the i-αppli standby screen
You can activate the software set as the i-αppli
standby screen.
On the i-αppli standby screen t
1
The i-αppli is activated and
at the bottom of the screen.
<Set i-αppli stand-by>
or flashes