NTT docomo FOMA SO706i Instruction Manual page 371

"Connection failed (403)"
● Connection to the site failed for some reason. Retry
connection.
"Connection interrupted"
● i-mode connection was interrupted due to poor
reception. Move to a location where the reception is
good before using the i-mode service. →p.44
● If this message appears when the signal is strong and
the " " mark is displayed, the connected site is very
busy. Retry later.
"Continue using i-αppli and transmit data?"
● This message appears when you selected "NO" or
"Terminate i-αppli" in response to "The number of
i-αppli communications is large. Continue
communication?" Select "YES" to continue i-αppli
communication. Select "Terminate i-αppli" to stop using
the i-αppli.
"Current UIM is not registered as IC owner Unable
to delete"
"Current UIM is not registered as IC owner Unable
to download"
"Current UIM is not registered as IC owner Unable
to move"
"Current UIM is not registered as IC owner Unable
to run"
"Current UIM is not registered as IC owner Unable
to upgrade"
● This message appears when the inserted UIM does not
match the UIM information registered for FeliCa or you
tried to run Osaifu-Keitai i-αppli.
"Data in IC card is full Unable to download Delete
service?"
"Data in IC card is full Unable to move Delete
service?"
"Data in IC card is full Unable to run Delete
service?"
"Data in IC card is full Unable to upgrade Delete
service?"
● This message appears when Osaifu-Keitai i-αppli is
downloaded or moved from a microSD card but there is
not enough data capacity left on the IC card. Select
"YES" to display a list of the Osaifu-Keitai service
names already registered, the space (bytes) which
would be freed by deleting each service, and the size of
the capacity shortage. Select one or more services to
delete, then follow the messages to start an i-αppli to
delete them.
"Data is too long A part is deleted"
● The size of address, subject or text or more than one
data exceeds the maximum, and the Compose
message screen appears with the excess part deleted.
"Data is too long Please delete message"
● The combined double-byte character count for the main
text and quotation symbols in a reply-with-quote i-mode
mail exceeds 5,000 characters. Delete text to bring the
count to 5,000 double-byte characters or less.
"Data transmission is frequent Continue
transmission?"
● This message appears when the number of
communications when using an i-αppli becomes very
large within a certain period. Select "Yes" to carry on
i-αppli communication, or "No" to stop communication.
Select "Terminate i-αppli" to stop using the i-αppli.
"Data transmission is frequent Press CLR and
confirm data transmission"
● This message appears when the number of
communications from an i-αppli standby screen
becomes very large within a certain period. Press t
to select whether or not to permit communications from
the i-αppli standby display, or to close the i-αppli
standby display. →p.199
"Dial/Receive calls activating Original lock"
● This message appears when you have attempted a
prohibited operation while the original lock is applied to
"Dial/sending mail".→ p.109
"Download failed"
● This message appears when a download of a melody,
Chara-den or download dictionary suffered a
communication error or improper data.
"Editing now Unable to delete"
● This message appears when you attempt to delete a
mail message saved in Draft while it is being edited.
"Enter correct Network Security Code"
● This message appears when an incorrect network
security code was input for a function which requires
network security code entry. Enter the correct network
security code. →p.100
"Error in image Does not work correctly"
● This message appears when a Flash movie cannot be
played due to an error found in the data.
"Error Register forwarding number"
● This message appears when you have subscribed to
the Call Forwarding service and attempt to forward an
incoming call by selecting "Call Forwarding" from the
function menu without setting the forwarding number.
→p.314
"Failed to Copy all"
● Copying could not be complete, for some reason.
Replace with a different microSD card and try to copy
again.
"Failed to Copy this"
● Copying could not be completed, for some reason.
Replace with a different microSD card and try to copy
again.
"Failed to read"
● Copying could not be completed, for some reason.
Replace with a different microSD card and try to copy
again.
Continued on next page
369