NTT docomo FOMA SO706i Instruction Manual page 373

"Message too long to add header"
● This message appears when the character count of the
text and header in total exceeds 5,000 double-byte
characters and the header cannot be added.
"Message too long to add header & signature"
● This message appears when you are forwarding
i-mode mail, but it was not possible to automatically
paste the header/signature because they would cause
the character count to exceed the limit of 5,000 double-
byte characters.
"Message too long to add signature"
● The signature cannot be pasted because the total of
main text and signature would exceed 5,000 double-
byte characters.
"No channel info"
● There is no channel information, and you cannot
compose a suggested message.
"No data"
● This message appears when there is no phonebook
entry that matches the search conditions when you
perform Phonebook search.
"No requested data Delete this shortcut icon?"
● This message appears when you select the shortcut
icon for data that has been deleted and attempt to start
it.
"No requested software"
● It is displayed when an i-αppli is started from mail,
Send Ir data function, Bar code reader, IC card or data
broadcast, and the relevant software is absent.
"No response"
● This message appears when the IC card authentication
function was used for user authentication, but
authentication timed out and failed. →p.111
"No response (408)"
● There was no response from the site, and
communication was cut off. Retry connection.
"No response Retry?"
(During infrared data exchange/iC communication)
● The receiving terminal cannot be found/detected. If
infrared communication is used, make sure the infrared
ports are facing each other. If iC communication is
used, check the FeliCa marks and place them together
again. You can select "YES", then press d to try
again.→pp.257, 259
"No Switch"
● This message appears when you cannot switch to a
videophone call during a voice call because the other
party is establishing a packet communication (including
i-mode). Check the other party's status and retry.
→ p.50
"Not correspond contents"
● The information acquired by the bar code reader
includes content not supported by this FOMA terminal,
so it cannot be recognized.
" おまかせロック設定中です "
● Omakase lock is set. While Omakase Lock is set, all
key operations are locked except receiving a voice call/
videophone call and turning the power on/off. →p.102
"Other function active Cannot start"
"Other function active Cannot operate"
● This message appears when you attempt an
unavailable operation when another function is running.
"Out of service area"
● This message appears when you attempt to use an
i-mode service outside the service area, or where the
radio waves do not reach. Move to a place where "
is displayed, then use the i-mode service. → p.44
"Page is not found (404)"
● The site is not found. It may not exist.
"Password is not correct (401)"
● This message appears when the authentication did not
go through on the "Authentication" or "Re-authentication"
screen. Select "YES" to retry authentication.
"Phone/UIM ID will be sent?"
● This may be displayed during viewing of an Internet
page or other site. Select "YES" to send your mobile
phone manufacturer number. Otherwise, select "NO".
→p.137
"PIN1 code blocked"
● This message appears when powered on during PIN1
code lock. Press d to display the input screen for the
PIN lock release code, then enter the PIN lock release
code correctly to unlock. → p.100
"Please wait for a while"
● The voice line or packet communication device may be
malfunctioning. Otherwise, the voice line/packet
communication network may be congested. Attempt to
use a voice call, videophone call or i-mode later.
You can still make an emergency call (110, 119 and
118). However, you may not be connected depending
on the condition.
"Please wait for a while (packet)"
● The packet communication device may be
malfunctioning. Otherwise, the packet communication
network may be congested. Retry later.
"PUK code blocked"
● This message appears when you turn on the power and
attempt a UIM operation while the PUK code is locked.
Contact a DOCOMO shop.→p.100
"Reading UIM Cannot start"
● This message appears when you attempt an operation
related to the UIM while it is being read. Please try
again later.
"Replace with a new one or check the disk"
● Run checkdisk on the microSD card. →p.247
Continued on next page
"
371