NTT docomo FOMA SO706i Instruction Manual page 471

AT command
AT+CLIR= Sets whether or not to notify
n
the other party of the phone
number when originating a
64K data communication
call.
AT+CMEE= Sets whether the error
n
report of the FOMA terminal
is present.
[&F] [&W]
AT+CNUM Displays the own number of
the FOMA terminal.
AT+COPS Selects the network
operator to connect.
Outline
= 0 : Complies to the CLIR service contract.
n
= 1 : Not notify the other party of the
n
= 2 : Notify the other party of the caller's
n
AT+CLIR?
： Displays the current setting.
+CLIR:
n
=0 : CLIR is not started (Caller ID is
m
= 1 : CLIR is started (Caller ID is always
m
= 2 : Unknown
m
= 3 : CLIR temporary mode (default is not
m
=4 : CLIR temporary mode (default is
m
= 0 : Use the ERROR result (initial value).
n
= 1 : +CME ERROR:<err> result code is
n
= 2 : +CME ERROR:<err> result code is used,
n
AT+CMEE?
： Displays the current setting.
The command displayed on the right is the
execution example for cases when there is a
FOMA terminal problem or a connection error.
+CME ERROR result code is as follows.
1：no connection to phone
10：SIM not inserted
15：SIM wrong
16：incorrect password
100：unknown
Result: +CNUM:,<number>,<type>
number: phone number
type : 129 or 145
129 ： International access code (+) is not
145 ： International access code (+) is
Format : AT+COPS=<mode>,2,<oper>
mode=0 : automatic (searches the network
mode=1 : manual (connects to the network
mode=2 : Disconnects the connection to the
mode=3 : Mapping is not performed.
mode=4 : manual/automatic (if the connection
<oper> is a hexadecimal value which consists
of Country code (MCC) and Network code
(MNC). The format is as follows:
Digit 1 of MCC･･･octet 1 bits 1 to 4
Digit 2 of MCC･･･octet 1 bits 5 to 8
Digit 3 of MCC･･･octet 2 bits 1 to 4
Digit 3 of MNC･･･octet 2 bits 5 to 8
Digit 2 of MNC･･･octet 3 bits 5 to 8
50
Parameter/description
caller's phone number.
phone number (initial value).
,
m
always sent)
not sent)
notify)
notify)
used, and a numeral value is used for
<err>.
and characters are used for <err>.
included.
included.
and switches the network operator
automatically)
operator specified in <oper>)
network operator
to the network operator specified in
<oper> fails, works as automatic
mode.)
Command execution example
AT+CLIR=0
OK
AT+CLIR?
+CLIR:0,1
OK
AT+CLIR=?
+CLIR:(0-2)
OK
AT+CMEE=0
OK
AT+CNUM
ERROR
AT+CMEE=1
OK
AT+CNUM
+CME ERROR:10
AT+CMEE=2
OK
AT+CNUM
+CME ERROR:SIM not
inserted
AT+CNUM
+CNUM:,"+8190XXXXX
XXX",145
OK
AT+COPS=0
OK
AT+COPS?
+COPS:0
OK
AT+COPS=?
+COPS:(2,,,"44F001"),
(3,,,"44F002"),,(0,1),(2)
OK