NTT docomo FOMA SO706i Instruction Manual page 470

AT command
AT+CBC Displays the battery status
of the FOMA terminal.
AT+CBST Changes the bearer service
type.
[&F] [&W]
AT+CEER Displays the reason for
disconnection of the
previous call.
AT+CGDCONT Sets the access point name
(APN) for packet origination.
AT+CGEQMIN Registers a criterion to be used
to decide whether or not to allow
the QoS (quality of service) that is
informed from the network side
when PPP packet
communication is established.
AT+CGEQREQ Sets the QoS (quality of
service) to be requested to
network when originating a
PPP packet communication.
AT+CGMR Displays the version of the
FOMA terminal.
AT+CGREG= Specifies whether to notify
n
the network registration
condition.
The returned notification
displays whether you are
inside or out of service.
[&F] [&W]
AT+CGSN Displays the product number
of the FOMA terminal.
AT+CLIP= Displays the other party's
n
Caller ID on a PC when a
64K data communication
call is received.
[&F] [&W]
Outline
Result: +CBC:<bcs>,<bcl>
bcs:
0 : FOMA terminal is powered by the battery.
1 : FOMA terminal is not powered by the battery.
2 : FOMA terminal is not connected to the battery.
3 : FOMA terminal is out of transmission due to
the power-supply error.
bcl:
0 : Battery has run out, or battery is not
connected.
1-100 : Battery remained
Format: AT+CBST=<
=116： 64,000bps (bit transparent) (initial
n
=134： 64,000bps (multimedia)
n
Result: +CEER:<report>
report: List of disconnection reasons (p.59).
p.56
p.56
p.57
−
= 0 : Not informed (initial value).
n
= 1 : Informed.
n
AT+CGREG?
： Displays the current setting.
+CGREG： <
−
= 0 : Not display the result (initial value)
n
= 1 : Display the result
n
AT+CLIP?
： Displays the current setting.
+CLIP:
n
= 0 : NW setting not notifying the other
m
= 1 : NW setting notifying the other party
m
= 2 : Unknown
m
49
Parameter/description
>,1,0
n
value)
Informed when switching between
"Inside the service area" and "Outside
the service area" is completed.
> , <stat>
n
: Set value
n
stat：
0: Out of packet area
1: Within packet area
4: Unknown
5: Within packet area
,
m
party of the Caller ID in outgoing call.
of the Caller ID in outgoing call.
Command execution example
AT+CBC
+CBC:0,70
OK
AT+CBC?
ERROR
AT+CBC=?
+CBC:(0-3),(0-100)
OK
AT+CBST=134,1,0
OK
AT+CBST?
+CBST:134,1,0
OK
AT+CBST=?
+CBST:(116,134),
(1),(0)
OK
AT+CEER
+CEER:36
OK
p.56
p.56
p.57
AT+CGMR
12345xxxxxxxxxxx
OK
AT+CGREG=1
OK (Set to informed)
AT+CGREG?
+CGREG: 1,0
OK
AT+CGREG=?
+CGREG: (0,1)
OK
(Outside the service area)
(When you move from
"outside the service
area" to "inside the
service area".)
+CGREG:1
AT+CGSN
12345xxxxxxxxxxx
OK
AT+CLIP=0
OK
AT+CLIP=?
+CLIP:(0,1)
OK
(A call is received when
+CLIP=1 is set)
RING
+CLIP:
"090XXXXXXXX",177,
"123",136