NTT docomo FOMA SO706i Instruction Manual page 469

AT command
AT&W Stores the current settings.
n
AT＊DANTE Displays the FOMA terminal
signal reception level.
AT＊DGANSM= Sets the reject/permit mode
n
setting for the packet
incoming call. This
command is effective for
those incoming packet calls
after the setting command is
input.
Sets APN, which permits
AT＊DGAPL= [,cid]
n
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
AT＊DGARL= [,cid] Sets APN, which rejects
n
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
AT＊DGPIR= This command validates the
n
setting for notifying Caller ID
when sending/receiving
packet communication.
Even in the dial up network
setting, you can also add
186 (notify) or 184 (not
notify) to the access point
number. (p.35)
AT＊DRPW Displays the indicator value
of the receiving power of the
FOMA terminal.
AT+CAOC Inquires for the current
charge.
Outline
Only = 0 can be specified (can be omitted).
n
0： FOMA terminal signal reception level is displayed as
out of area.
1： FOMA terminal signal reception level is 0 or 1
bar.
2： FOMA terminal signal reception level is 2 bars.
3： FOMA terminal signal reception level is 3 bars.
= 0 ： Disables the incoming call reject (AT＊
n
= 1 ： Enables the incoming call reject
n
= 2 ： Enables the incoming call permit
n
AT ＊ DGANSM?
： Displays the current setting.
= 0 ： Adds the APN defined by <cid> to
n
= 1 : Deletes the APN defined by <cid>
n
If <cid> is omitted, this will apply to all cid.
AT ＊ DGAPL?
： Displays incoming call permission list.
= 0 : Adds the APN defined by <cid> to
n
= 1 : Deletes the APN defined by <cid>
n
If <cid> is omitted, this will apply to all cid.
AT ＊ DGARL?
： Displays incoming call rejection list.
= 0 : Uses APN as it is (initial value).
n
= 1 : Uses APN by adding "184". (Caller ID
n
= 2 : Uses APN by adding "186". (Caller ID
n
AT ＊ DGPIR?
： Displays the current setting.
−
−
48
Parameter/description
DGARL)/permit setting (AT＊DGAPL) (initial
value).
setting.
setting.
incoming call permission list.
from incoming call permission list.
incoming call rejection list.
from incoming call rejection list.
is always not sent.)
is always sent.)
Command execution example
AT&W0
OK
AT&W
OK
AT&W?
ERROR
AT&W＝?
ERROR
AT＊DANTE
＊DANTE:3
OK
AT＊DANTE＝?
＊DANTE:(0-3)
OK
AT＊DGANSM=0
OK
AT＊DGANSM?
＊DGANSM:0
OK
AT＊DGAPL =0,1
OK
AT＊DGAPL?
＊DGAPL:1
OK
AT＊DGAPL =1
OK
AT＊DGAPL?
OK
AT＊DGARL =0,1
OK
AT＊DGARL?
＊DGARL:1
OK
AT＊DGARL =1
OK
AT＊DGARL?
OK
AT＊DGPIR =0
OK
AT＊DGPIR?
＊DGPIR:0
OK
AT＊DRPW
＊DRPW:0
OK
AT＊DRPW=?
＊DRPW:(0-75)
OK
AT+CAOC
+CAOC:"000014"
OK