Veikong gpd 515/g5 Startup Manual page 14

QUICK REFERENCE FOR GPD 515/G5 PARAMETERS (FACTORY SET)
PARAMETER FACTORY USER
NUMBER SETTING SETTING
(7)
F4-01 2
F4-02 1.00
F4-03 3
F4-04 0.50
F4-05 0.0
F4-06 0.0
F5-01 0
F5-02 1
F6-01 0
F7-01 1
F8-01 1
F9-01 0
F9-02 0
F9-03 1
F9-04 0
F9-05 1
F9-06 1
H1-01 24
H1-02 14
H1-03 3 (0) (3)
H1-04 4 (3) (3)
H1-05 6 (4) (3)
H1-06 8 (6) (3)
H2-01 0
H2-02 1
H2-03 2
H3-01 0
H3-02 100.0
H3-03 0.0
H3-04 0
H3-05 0
H3-06 100.0
H3-07 0.0
H3-08 2
H3-09 1F
H3-10 100.0
H3-11 0.0
H3-12 0.00
(1) To establish a custom User Access Level, refer to paragraph 5.4.
(2) Initial value is related to V/f curve selected by E1-03 setting.
(3) Settings in parentheses reflect 3-wire control initialization values.
(4) Monitor displays ( UX-XX ) are display or output selections, rather than parameter setup; therefore, user setting is not
possible.
(5) Factory setting depends on drive rating. See Table A3-1.
(6) Factory setting depends on Control Method ( A1-02 ).
(7) Not all parameters are accessible in all Access Levels ( A1-01 ) and Control Methods ( A1-02 ); see Section 5.
(8) Only effective with PG-D2 or PG-B2 option card; see instruction sheet 2Y25-396.
(9) Only effective with AI-14B or AI-14U option card; see instruction sheet 2Y25-296 or -295.
(10) Only effective with DI-08 or DI-16H2 option card; see instruction sheet 2Y25-294 or -400.
(11) Only effective with AO-08, AO-12 or AO-12B2 option card; see instruction sheet 2Y25-297 or -438.
(12) Only effective with DO-02C option card; see instruction sheet 2Y25-402.
(13) Only effective with DO-08 option card; see instruction sheet 2Y25-350.
(14) Only effective with PO-36F option card; see instruction sheet 2Y25-298.
PARA.
PARAMETER FACTORY
REF.
NUMBER SETTING
(7)
(11)
H4-01
(11) H4-02 1.00
(11) H4-03
(11)
H4-04
(11)
H4-05 0.50
(11)
H4-06
(12)
H4-07
(12)
H5-01
(13)
H5-02
(14)
H5-03
H5-04
p. A1-17
H5-05
p. A1-17
p. A1-17
L1-01
p. A1-17
L1-02
p. A1-17
L2-01
p. A1-17
L2-02 0.7 (5)
p. A1-17
L2-03 0.5 (5)
5.32
L2-04
5.32
L2-05
5.32
L2-06
5.32 L3-01
5.32 L3-02
5.32
L3-03
5.33
L3-04
5.33
L3-05
5.33
L3-06
5.19
L4-01
5.18
L4-02
5.18
L4-03
5.19
L4-04
5.30
L4-05
5.18
L5-01
5.18
L5-02
5.19
L6-01
5.30
L6-02
5.18
L6-03
5.18
p. A1-19
USER PARA.
SETTING REF.
2 5.31
5.31
0.0 5.31
3 5.31
5.31
0.0 5.31
0 5.31
1F 5.28
3 5.28
0 5.28
3 5.28
1 5.28
1 5.41
8.0 5.41
0 5.29
5.29
5.32 D
(5) 190, 5.29
190 380, or 5.29
0.0 546 (5) p. A1-21
1 5.39
150 5.39
50 5.39
1 5.39
1 5.39
160 5.39
0.0 5.33
2.0 5.33
0.0 5.33
2.0 5.33
0 5.20
0 5.5
0 5.5
0 5.44
150 5.44
0.1 5.44
xv
PARAMETER FACTORY USER
NUMBER SETTING SETTING
(7)
L6-04 0
L6-05 150
L6-06 0.1
L7-01 200
L7-02 200
L7-03 200
L7-04 200
L8-01 0
L8-02 (5)
L8-03 3
L8-05 0
L8-07 1
L8-10 1
L8-17 1
L8-19 0
o1-01 6
o1-02 1
o1-03 0
o1-04 0
o1-05 0
o2-01 1
o2-02 1
o2-03 0
o2-04 (5)
o2-05 0
o2-06 1
o2-07 00000
o2-08 0
o2-09 1
U1-01
thru (4) ——
U1-34
U2-01
thru (4) ——
U2-14
U3-01
thru (4) ——
U3-08
PARA.
REF.
5.44
5.44
5.44
5.45
5.45
5.45
5.45
5.27
5.27
5.27
5.34
5.35
5.27
5.27
5.27
5.12
5.12
5.11
5.11
5.11
5.26
5.26
5.46
p. A3-1
5.26
5.26
5.26
5.26
p. A1-26
(4)
(4)
(4)