Epson S1C33210 Technical Manual page 312

III PERIPHERAL BLOCK: CLOCK TIMER
Register name Address Bit
Clock timer 0040159 D7–6
minute (B) D5
comparison D4
register D3
D2
D1
D0
Clock timer 004015A D7–5
hour (B) D4
comparison D3
register D2
D1
D0
Clock timer 004015B D7–5
day (B) D4
comparison D3
register D2
D1
D0
Clock timer 004026B D7–3
interrupt (B) D2
priority register D1
D0
Port input 4–7, 0040277 D7–6
clock timer, (B) D5
A/D interrupt D4
enable register D3
D2
D1
D0
Port input 4–7, 0040287 D7–6
clock timer, A/D (B) D5
interrupt factor D4
flag register D3
D2
D1
D0
TCRST: Clock timer reset (D1) / Clock timer Run/Stop register (0x40151)
Resets the clock timer.
Write "1": The clock timer is reset
Write "0": Invalid
Read: Always "0"
The clock timer is reset by writing "1" to TCRST when the timer is inactive. All timer counters are cleared to "0".
The clock timer cannot be reset when in the RUN state, nor can it be reset at the same time it is made to RUN
through the execution of one write to address 0x40151. (The clock timer is started, but not reset.) In this case, first
reset the clock timer and then use another instruction to RUN the clock timer. When the counters are cleared as the
clock timer is reset, an interrupt may be generated, depending on the register settings. Therefore, before resetting the
clock timer, first disable the clock timer interrupt, and after resetting the clock timer, reset the interrupt factor flag
and the interrupt factor and alarm factor generation flags.
Writing "0" to TCRST results in No Operation. Since this TCRST is a write-only bit, its value when read is always
"0".
The clock timer is not reset by an initial reset.
B-III-7-8
Name Function
– reserved
TCCH5 Clock timer minute comparison
TCCH4 data
TCCH3 TCCH5 = MSB
TCCH2 TCCH0 = LSB
TCCH1
TCCH0
– reserved
TCCD4 Clock timer hour comparison data
TCCD3 TCCD4 = MSB
TCCD2 TCCD0 = LSB
TCCD1
TCCD0
– reserved
TCCN4 Clock timer day comparison data
TCCN3 TCCN4 = MSB
TCCN2 TCCN0 = LSB
TCCN1
TCCN0
– reserved
PCTM2 Clock timer interrupt level
PCTM1
PCTM0
– reserved
EP7 Port input 7
EP6 Port input 6
EP5 Port input 5
EP4 Port input 4
ECTM Clock timer
EADE A/D converter
– reserved
FP7 Port input 7
FP6 Port input 6
FP5 Port input 5
FP4 Port input 4
FCTM Clock timer
FADE A/D converter
Setting
–
0 to 59 minutes
(Note) Can be set within 0–63.
–
0 to 23 hours
(Note) Can be set within 0–31.
–
0 to 31 days
–
0 to 7
–
1 Enabled 0 Disabled
–
1 Factor is 0 No factor is
generated generated
EPSON
Init. R/W Remarks
– – 0 when being read.
X R/W
X
X
X
X
X
– – 0 when being read.
X R/W
X
X
X
X
– – 0 when being read.
X R/W Compared with
X TCND[4:0].
X
X
X
– – Writing 1 not allowed.
X R/W
X
X
– – 0 when being read.
0 R/W
0 R/W
0 R/W
0 R/W
0 R/W
0 R/W
– – 0 when being read.
X R/W
X R/W
X R/W
X R/W
X R/W
X R/W
S1C33210 FUNCTION PART