Epson S1C33210 Technical Manual page 189

A18SZ:Areas 18–17 device size selection (DE) / Areas 18–15 set-up register (0x48120)
A16SZ:Areas 16–15 device size selection (D6) / Areas 18–15 set-up register (0x48120)
A14SZ:Areas 14–13 device size selection (D6) / Areas 14–13 set-up register (0x48122)
A12SZ:Areas 12–11 device size selection (D6) / Areas 12–11 set-up register (0x48124)
A10SZ:Areas 10–9 device size selection (D6) / Areas 10–9 set-up register (0x48126)
A8SZ: Areas 8–7 device size selection (D6) / Areas 8–7 set-up register (0x48128)
A5SZ: Areas 5–4 device size selection (D6) / Areas 6–4 set-up register (0x4812A)
Select the size of the device connected to each area.
Write "1": 8 bits
Write "0": 16 bits
Read: Valid
A device size can be selected for every two areas.
An 8-bit size is selected by writing "1" to AxxSZ and a 16-bit size is selected by writing "0" to AxxSZ.
Area 6 has its first half (0x300000 through 0x37FFFF) fixed to an 8-bit device and the last half (0x380000 through
0x3FFFFF) fixed to a 16-bit device.
At cold start, these bits are set to "0" (16 bits). At hot start, these bits retain their status before being initialized.
A18DF1–A18DF0:
Areas 18–17 output disable delay time (D[D:C]) / Areas 18–15 set-up register (0x48120)
A16DF1–A16DF0:
Areas 16–15 output disable delay time (D[5:4]) / Areas 18–15 set-up register (0x48120)
A14DF1–A14DF0:
Areas 14–13 output disable delay time (D[5:4]) / Areas 14–13 set-up register (0x48122)
A12DF1–A12DF0:
Areas 12–11 output disable delay time (D[5:4]) / Areas 12–11 set-up register (0x48124)
A10DF1–A10DF0:
Areas 10–9 output disable delay time (D[5:4]) / Areas 10–9 set-up register (0x48126)
A8DF1–A8DF0:
Areas 8–7 output disable delay time (D[5:4]) / Areas 8–7 set-up register (0x48128)
A6DF1–A6DF0:
Area 6 output disable delay time (D[D:C]) / Areas 6–4 set-up register (0x4812A)
A5DF1–A5DF0:
Areas 5–4 output disable delay time (D[5:4]) / Areas 6–4 set-up register (0x4812A)
Set the output-disable delay time.
When using a device that has a long output-disable time, set a delay time to ensure that no contention for the data bus
occurs during the bus operation immediately after a device is read.
At cold start, these bits are set to "11" (3.5 cycles). At hot start, the bits retain their status before being initialized.
A18WT2–A18WT0: Areas 18–17 wait control (D[A:8]) / Areas 18–15 set-up register (0x48120)
A16WT2–A16WT0: Areas 16–15 wait control (D[2:0]) / Areas 18–15 set-up register (0x48120)
A14WT2–A14WT0: Areas 14–13 wait control (D[2:0]) / Areas 14–13 set-up register (0x48122)
A12WT2–A12WT0: Areas 12–11 wait control (D[2:0]) / Areas 12–11 set-up register (0x48124)
A10WT2–A10WT0: Areas 10–9 wait control (D[2:0]) / Areas 10–9 set-up register (0x48126)
A8WT2–A8WT0: Areas 8–7 wait control (D[2:0]) / Areas 8–7 set-up register (0x48128)
A6WT2–A6WT0: Area 6 wait control (D[A:8]) / Areas 6–4 set-up register (0x4812A)
A5WT2–A5WT0: Areas 5–4 wait control (D[2:0]) / Areas 6–4 set-up register (0x4812A)
Set the number of wait cycles to be inserted when accessing an SRAM device.
The values 0 through 7 written to the control bits equal the number of wait cycles inserted.
Note that the write cycle consists of a minimum of two cycles, so that a writing 0 or 1 is invalid.
When an SRAM device is connected, wait cycles derived via the #WAIT pin can also be inserted. In this case too, the
wait cycles set by AxxWT are valid.
The DRAM read/write cycles do not have wait cycles inserted that are set by AxxWT or derived from the #WAIT
pin.
The burst read cycle of a burst ROM (except for the first access) also does not have any wait cycle inserted. The first
read cycle of a burst ROM and the write cycle to the burst ROM area have wait cycles inserted that are set by
AxxWT . Wait cycles derived from the #WAIT pin also can be inserted in the cycle for writing to the burst ROM area.
S1C33210 FUNCTION PART
Table 4.22 Output Disable Delay Time
AxxDF1 AxxDF0
1 1
1 0
0 1
0 0
EPSON
II CORE BLOCK: BCU (Bus Control Unit)
Delay time
3.5 cycles
2.5 cycles
1.5 cycles
0.5 cycles
B-II-4-37