Canon iR6570 series Service Manual page 551

Code Description
0001 An error has occurred at time of NE controller
start-up.
The NE controller that was connected before
power-off is not connected at power-on.
0002 There is an IP error while the NE controller is in
operation.
The IPC may have an open circuit or the IPC
communication cannot be recovered.
E719 There is a fault in the coin vendor.
After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)
0001 An error has occurred at time of coin vendor start-
up.
The coin vendor was connected before power-off,
but is not connected at power-on.
0002 An IPC error has occurred while the coin vendor is
in operation.
The IPC may have an open circuit, or the IPC
communication cannot be removed.
The pickup/delivery signal line has an open circuit.
An illegal connection has been detected.
0003 While a unit price is being obtained at start-up, an
error has occurred in the communication with the
coin vendor.
0011 An error has occurred at card reader start-up.
The card reader that was connected before power-
off is not connected at power-on.
0012 An IPC error has occurred while the card reader is
in operation.
The IPC may have an open circuit, or the IPC
communication cannot be recovered.
E730 There is a fault in the PDL software.
1001 There is an initialization error.
100A An error has occurred that can be fatal to the
system (e.g., initialization error).
9004 There is a fault in the PAI communication with an
outside controller.
9005 There is a fault in video connection with an
external controller.
A006 absence of PDL response: there is no PDL response
because of a fault in or the absence of Subbootable.
A007 There is a mismatch in version between the
machine control software and the PDL control
software.
B013 The font data is corrupted.
E732 There is a fault in the reader communication.
0001 There is a DDI-S communication error.
E733 There is a fault in the printer communication.
0000 The attempt at communication with the printer fails
at start-up.
0001 There is a DDI-P communication error.
E740 There is a fault in the Ethernet board.
0002 The MAC address is illegal.
E743 There is a fault in the DDI communication.
0000 An SCI error has occurred; the reception data is
faulty; a reception time-out error has occurred; a
SEQ time-out error has occurred
E744 There is a fault in the language file/boot ROM.
Remedy
- Check the connection of the cable.
- Check the connector of the cable.
- Execute PDL resetting.
- Turn off and then on the main power.
- Turn off and then back on the main power.
- Check the open I/F board and cable connection.
- Replace the external controller open I/F board.
- Replace the main controller PCB.
- Execute PDL resetting.
- Turn off and then on the main power.
- Check the connection of the SURF board.
- Re-install the firmware.
- Replace the main controller PCB.
- Execute PDL resetting.
- Turn off and then on the main power.
- Execute full formatting and install the system
software.
- Turn off and then on the main power.
- Re-install the system software.
- Execute full formatting and install the system
software.
- Check the communication between the reader
unit and the main controller.
- Check the power supply of the reader unit.
(Check to see if initialization takes place at start-
up.)
- Replace the reader controller PCB, reader relay
PCB, or main controller PCB.
- Check the connection of the cable between the
DC controller and the main controller.
- Check the power supply of the printer. (Check to
see if initialization takes place at start-up.)
- Replace the DC controller PCB or the main
controller PCB.
- Replace the main controller PCB.
- Disconnect and then connect the connector
between the reader unit and the printer unit.
- Replace the cable, reader controller PCB, and
main controller PCB.
Chapter 15
15-11