Canon iR6570 series Service Manual page 546

Chapter 15
Code
E505
E514
E519
E530
E531
E532
E535
E537
15-6
Description
0002 There is an error in the communication between the
finisher and the saddle unit.
0003 There is an error in the communication between the
finisher and the punch unit.
There is a finisher backup memory error (finisher).
0001 An error has occurred in the data stored in the
backup memory.
0002 There is an error in the punch unit EEPROM data. - Turn off the main power; check the DC
There is a trailing edge assist motor error (finisher).
8001 The home position sensor does not go off even
when the trailing edge assist motor has rotated for
a specific period of time.
8002 The home position sensor does not go on even
when the trailing edge assist motor has rotated for
a specific period of time.
There is a gear change motor error (finisher).
8001 The home position sensor does not go off even
when the gear change motor has rotated for a
specific period of time.
0002 The home position sensor does not go on even
when the gear change motor has rotated for a
specific period of time.
There is a front alignment error. (finisher)
8001 The home position sensor does not go off even
when the front alignment motor has rotated for a
specific period of time.
8002 The home position sensor does not go on even
when the front alignment sensor has rotated for a
specific period of time.
There is a stapling error. (finisher)
0001 The home position sensor does not go off even
when the stapler motor has rotated for a specific
period of time.
0002 The home position sensor does not go on even
when the stapler motor has rotated for a specific
period time.
There is a stapler shift error. (finisher)
8001 The home position sensor does not go off even
when the stapler shift motor has rotated for a
specific period of time.
8002 The home position sensor does not go on even
when the stapler shift motor has rotated for a
specific period of time.
There is a swing error. (finisher)
8001 The home position sensor does not go off even
when the wiring motor has rotated for a specific
period of time.
8002 The home position sensor does not go on even
when the swing motor has rotated for a specific
period of time.
There is a rear alignment error. (finisher)
Remedy
- Check the connection between the saddle
stitcher controller PCB and the finisher controller
PCB.
- Check the communication between the saddle
stitcher controller PCB and the finisher controller
PCB.
- Turn off the main power; check the DC
controller PCB and the finisher controller PCB for
wiring; check the 24-V system fuse; then, turn the
main power back on.
controller PCB and the puncher controller PCB
for wiring; then, check the 24-V system fuse;
then, turn the main power back on.
1. Check the trailing edge assist home position
sensor. Is the sensor normal?
2. Check the wiring between the finisher
controller PCB and the trailing edge assist motor.
Is it normal?
3. Check the trailing edge assist mechanism. Is
there a fault?
4. Try replacing the trailing edge assist motor. Is
the problem corrected?
1. Check the gear change home position sensor. Is
the sensor normal?
2. Check the wiring between the finisher
controller PCB and the change motor. Is it
normal?
3. Check the gear change mechanism. Is there a
fault?
4. Try changing the gear change motor. Is the
problem corrected?
1. Check the aligning plate home position sensor.
Is it normal?
2. Check the wiring between the finisher
controller PCB and the aligning plate front motor.
Is it normal?
3. Is there any mechanical obstacle in the path in
which the aligning plate moves?
4. Try replacing the aligning plate front motor. Is
the problem corrected?
1. Check the wiring between the finisher
controller PCB and the stapler. Is it normal?
2. Try replacing the stapler. Is the problem
corrected?
1. Check the stapler shift home position sensor. Is
the sensor normal?
2. Check the wiring between the finisher
controller PCB and the stapler shift motor. Is it
normal?
3. Is there any mechanical obstacle in the path of
the stapler shift base?
4. Try replacing the stapler shift motor. Is the
problem corrected?
1. Check the wiring home position sensor. Is it
normal?
2. Check the wiring between the finisher
controller PCB and the swing motor. Is it normal?
3. Is there a fault in the swing mechanism?
4. Try replacing the swing motor. Is the problem
corrected?