Pos : 67.20.1 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/IP-Adres se mi t " WAGO Ethernet Setti ngs" vergeben - Ü bersc hrift 3 @ 4\mod_1239022358609_21.doc x @ 29973 @ 3 @ 1

Eine nähere Ang abe von J ürgen er hal

8.2.3

Assigning IP Address via "WAGO Ethernet Settings"

Pos : null /Alle Serien ( Allgemei ne Modul e)/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Softwarekompati bilität beac hten! @ 33\mod_1547563918553_21.doc x @ 523149 @ @ 1

Note Software Compatibility!

Refer to the version of the software specified in "Software Compatibility" in the

Technical Data.

Pos : 67.20.3 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/IP-Adres se mi t " WAGO Ethernet Setti ngs" vergeben - Programm dient daz u, IP, Default, Flash wieder her @ 5\mod_1243598804994_21.doc x @ 34616 @ @ 1

This program is used to configure an IP address, to reset the fieldbus

coupler/controller parameters to the factory settings and to restore the Flash File

System in which the WBM pages of the fieldbus coupler/controller are stored.

Pos : null /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/F eldbus knoten i n Betri eb nehmen/U ntergruppen/IP- Adr ess e mit " WAGO Ether net Settings" vergeben - kann üb seriell Ser vice- Schni oder ETHERN ET-Schni @ 32\mod_1535725056787_21.doc x @ 497999 @ @ 1

"WAGO Ethernet Settings" can be used via the serial service interface or via the

ETHERNET interface.

For initial commissioning, however, the way via the serial service interface is

described here, because for access via the ETHERNET interface the currently

assigned IP address must already be known.

Pos : 67.20.5 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Z ur Datenkommuni kation können Kommuni kati ons kabel oder WAGO-F unkadapter ver wendet werden. @ 5\mod_1243599181347_21.doc x @ 34623 @ @ 1

WAGO communication cables or WAGO radio-link adapters can be used for data

communication via the serial service interface.

Pos : 67.20.6 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Hinweis: Kommuni kati ons kabel 750-920 nic ht unter Spannung s tec ken! (Koppler/C ontroll er) @ 4\mod_1239172916562_21.doc x @ 30343 @ @ 1

Do not connect Communication Cable when energized!

To prevent damage to the service interface, do not connect or disconnect 750-

920 respectively 750-923 Communication Cable when energized! The fieldbus

coupler/controller must be de-energized!

Pos : null /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/F eldbus knoten i n Betri eb nehmen/Hi nweis : F ür IP-Adress vergabe über Softwar e,Adr ess wahlsc halter auf 0 stellen! (BootP/ETH Settin) 89x @ 34\mod_1550494429178_21.doc x @ 530786 @ @ 1

Set the address selection switch to 0 for an IP assignment via software!

Set the address selection switch to "0" to disable the DIP switch.

Restart the fieldbus node after adjusting the address selection switch to apply the

configuration changes.

Pos : null /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/F eldbus knoten i n Betri eb nehmen/Ver binden Sie di e s eri. Sc hnittst. Ihres PCs unt. Ver wend. ei nes WAGO- Kommkabels 1. (Kopfstati on) @ 34\mod_1550746952128_21.doc x @ 532491 @ @ 1

Using a WAGO Communication cable 750-920 respectively 750-923,

connect your PC with the service interface of the head station of the

fieldbus node.

Pos : 67.20.9 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/IP-Adres se mi t " WAGO Ethernet Setti ngs" vergeben, Sc hritt 4,5,6: E-S starten, Identifiz ., R eg N etz w @ 5\mod_1243935722127_21.doc x @ 34657 @ @ 1

Start "WAGO Ethernet Settings" program.

Click on [Read] to read in and identify the connected fieldbus node.

Select the Network tab.

Pos : 67.20.10 /Seri e 750 ( WAGO-I/O-SYSTEM)/In Betrieb nehmen/Fel dbus knoten in Betrieb nehmen/IP- Adr ess e mit "WAGO Ether net Settings" vergeben, Schritt 7 "Stati sche Konfig urati on" Reg "N etz wer k" @ 21\mod_1416841859547_21.doc x @ 168832 @ @ 1

To assign a permanent address, select the option "Static configuration" in

the field Source (DHCP is the default).

Pos : 67.20.11 /Seri e 750 ( WAGO-I/O-SYSTEM)/In Betrieb nehmen/Fel dbus knoten in Betrieb nehmen/IP- Adr ess e mit "WAGO Ether net Settings" vergeben, Schritt 8 Geben Sie di e IP-Adress e ein @ 5\mod_1244199539786_21.doc x @ 34993 @ @ 1

Commissioning

Manual

Version 1.3.0

Table of Contents