Assigning The Ip Address Via Bootp - WAGO -I/O-SYSTEM 750 XTR Manual

92 Commissioning
Enter the required IP Address and, if applicable, the address of the subnet
6.
mask and gateway.
Pos : 67.20.12 /Seri e 750 ( WAGO-I/O-SYSTEM)/In Betrieb nehmen/Fel dbus knoten in Betrieb nehmen/IP- Adr ess e mit "WAGO Ether net Settings" vergeben, Schritt 9 bis 10 IP über nehmen, WBM öffnen @ 5\mod_1244199645897_21.doc x @ 34997 @ @ 1
7. Click on the [Write] button to apply the settings in the fieldbus node.
8. You can now close "WAGO Ethernet Settings" or make other changes in
the Web-based Management System as required. To open the Web-based
Management System click on the button [Start WBM] on the right side.
Pos : 67.21 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Pos : 67.22.1 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/IP-Adres se mi t einem BootP-Ser ver vergeben ( Koppler) @ 7\mod_1273501206434_21.doc x @ 56281 @ 3 @ 1
8.2.4

Assigning the IP Address via BootP

A BootP server can be used to assign a fixed IP address.
Assigning the IP address using a BootP server depends on the respective BootP
program. Handling is described in the respective manual for the program or in the
respective integrated help texts.
Pos : 67.22.2 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Hinweis: F ür akti ve Softwar e-Konfig urati on, Adr ess wahlsc halter auf 0 stellen! (BootP) @ 5\mod_1244020081653_21.doc x @ 34753 @ @ 1
Set the address selection switch to 0 for active software configuration!
Set the address selection switch to 0 to disable the DIP switch.
If an access to the internal Web pages of WBM is already possible via an IP
address, then the software configuration via the WBM can be done.
In the default status, configuration via DHCP is activated.
If not yet been assigned IP address, you can otherwise use "WAGO Ethernet
Settings" or enable BootP in the Network tab of "WAGO Ethernet Settings".
Restart the fieldbus node after adjusting the address selection switch to apply the
configuration changes.
Pos : 67.22.3 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Hinweis: IP-Adress vergabe nic ht über Router möglich! @ 9\mod_1281680971860_21.doc x @ 63546 @ @ 1
IP address assignment is not possible via the router!
The IP address is assigned via patch cable, switches or hubs. Addresses cannot
be assigned via routers.
Pos : 67.22.4 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Hinweis: BootP muss i m Web- Bas ed-Manag ement-System akti vi ert s ein! @ 9\mod_1281681388997_21.doc x @ 63558 @ @ 1
BootP must be enabled on the Web pages!
Note that BootP must be enabled on the internal Web pages of the WBM, HTML
page "Port configuration".
BootP is enabled by default when delivered.
Pos : 67.22.5 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Infor mation: IP-Adr ess vergabe mit BootP- Ser ver auch unter Li nux. Beliebig er BootP- Ser ver @ 9\mod_1281681162420_21.doc x @ 63552 @ @ 1
Additional Information
Assigning IP addresses using a BootP server can be carried out in any Windows
and Linux operating system. Any BootP server may be used.
Pos : 67.22.6 /Serie 750 ( WAGO-I/O- SYST EM)/In Betri eb nehmen/F eldbus knoten in Betri eb nehmen/Die Besc hrei bung umfasst di e folgenden Ar beitssc hritte: M AC-ID,... (gekürz t für uns pez. BootP) @ 6\mod_1265027842746_21.doc x @ 49105 @ @ 1
Manual
Version 1.3.0
WAGO-I/O-SYSTEM 750 XTR
750-352/040-000 FC ETHERNET G3 XTR