Xerox WorkCentre 4150 Service Manual page 545

NOTE: In Table 6 the only features currently available for the 4265 are 10-155 Labels Temper-
ature Offset, and 10-200 Fuser Life Page Counter.
Table 6 NVM chain 10
Location NVM Name NVM Description
10-100 Standby Temper- Target temperature during
ature Offset standby mode.
10-105 Run Temperature Target temperature during run
Offset mode.
10-110 Low Power Tem- Target temperature during
perature Offset power save mode.
10-115 101-185 mm Offset temperature required on
Temperature Off- thermistor B for paper width.
set
10-120 186-216 mm Offset temperature required on
Temperature Off- thermistor B for paper width.
set
10-125 60gms Tempera- Media type offset for fuser roll
ture Offset temperature.
10-130 90gms Tempera- Media type offset for fuser roll
ture Offset temperature.
10-135 Bond Tempera- Media type offset for fuser roll
ture Offset temperature.
10-140 Transparency Media type offset for fuser roll
Temperature Off- temperature.
set
10-145 Cardstock Tem- Media type offset for fuser roll
perature Offset temperature.
10-150 Envelopes Tem- Media type offset for fuser roll
perature Offset temperature.
10-155 Labels Tempera- Media type offset for fuser roll
ture Offset temperature.
10-200 Fuser Life Page (Read only)
Counter
10-210 Heat Roll Life (Read only)
Page Counter
10-220 Pressure Roll Life (Read only)
Page Counter
General Procedures and Information
dC131
Location NVM Name
10-300
Value Default
10-310
0 to 15 (4 steps/ 10
5 degrees inter-
val)
0 to 10 (3 steps/ 5
5 degree inter-
Location NVM Name
vals)
11-100
0 to 40 (9 steps/ 20
5 degree inter-
vals)
11-105
0 to 15 (4 steps/ 5
5 degree inter-
vals) 11-110
0 to 15 (4 steps/ 5
5 degree inter- 11-200
vals)
0 to 15 (4 steps/ 5
5 degree inter- 11-205
vals)
0 to 10 (3 steps/ 5
5 degree inter- 11-210
vals)
0 to 10 (3 steps/ 5
5 degree inter- 11-300
vals)
0 to 10 (3 steps/ 5
5 degree inter- 11-305
vals)
0 to 10 (3 steps/ 5
5 degree inter- 11-310
vals)
0 to 10 (3 steps/ 5
5 degree inter-
vals) NOTE: For the 4265 machine, the path to NVM Chain 20 is Diagnostics > Fax & NW Diag-
nostics > dC 131 NVM Read/Write-Fax.
0 to 10 (3 steps/ 5
5 degree inter-
vals)
Location NVM Name
20-100
20-110
20-200
January 2016
6-60
Table 6 NVM chain 10
NVM Description
Pick-up Interval Change the time interval for
Delay paper pick-up.
Pick-up Interval Change the time interval for
Delay (Special paper pick-up.
Paper)
Table 7 NVM chain 11 (4265)
NVM Description
Platen Leading Check for Platen Leading
Edge Edge being within specifica-
tion.
Platen Side Edge Check for Platen Side Edge
being within specification.
Platen Magnifica- Check for Platen Magnifica-
tion tion being within specification.
DADF Bottom Check for DADF Bottom Lead-
Leading Edge ing Edge being within specifi-
cation.
DADF Bottom Check for DADF Bottom Side
Side Edge Edge being within specifica-
tion.
DADF Bottom Check for the DADF Bottom
Magnification Magnification being within
specification.
DADF Top Lead- Check for DADF Top Leading
ing Edge Edge being within specifica-
tion.
DADF Top Side Check for DADF Top Side
Edge Edge being within specifica-
tion.
DADF Top Magni- Check for DADF Top Magnifi-
fication cation being within specifica-
tion.
Table 8 NVM chain 20
NVM Description
Redial Attempts Number of times to
redial.
Redial interval Time between each
redial.
Pause Dial Time Time of each pause.
WorkCentre 4150/4250/4260WorkCentre 4150/4250/4260WorkCentre Work-
Value Default
0 to 100 msec. 0
0 to 100 msec. 0
Value Default
30 30
30 30
1000 1000
30 30
30 30
1000 1000
30 30
30 30
1000 1000
Value Default
1 to 13 7
1 to 15 3
0 to 200 (1000 msec.) 4