Iq3 Black Copies Or Prints Rap - Xerox WorkCentre 4150 Service Manual

• Check the spring contacts in the terminal assembly,
spring contacts supply the voltages to the xerographic module and the side
cover assembly. If necessary, clean the spring contacts. If necessary, install a
new terminal assembly, PL 4.15 Item
• Check the wiring between CON2 on the
4.15 Item 13.
• Check the wiring between CON1 on the
• Check the xerographic module ground connector,
that the connector is grounded.
• Install a new HVPS, PL 1.15 Item
• Install a new side cover assembly,
i. (4265) Refer to Wiring Diagram 34.
• Check the spring contacts in the terminal assembly,
spring contacts supply the voltages to the xerographic module and the side
cover assembly. If necessary, clean the spring contacts. If necessary, install a
new terminal assembly, PL 4.15 Item
• Check the wiring between CON2 on the
4.15 Item 13.
• Check the wiring between CON1 on the
• Check the xerographic module ground connector,
that the connector is grounded.
• Install a new HVPS, PL 1.15 Item
• Install a new side cover assembly,
j. Perform the OF5 Main PWB Check RAP.
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
PL 4.15 Item
13.
HVPS and the terminal assembly,
HVPS and CN7 on the Main PWB.
PL 4.15 Item 26. Make sure
2.
PL 7.30 Item 1.
Perform the following:
PL 4.15 Item
13.
HVPS and the terminal assembly,
HVPS and CN13 on the Main PWB.
PL 4.15 Item 26. Make sure
2.
PL 7.30 Item 1.
13. The

IQ3 Black Copies or Prints RAP

Use this RAP when the machine produces black copies and prints.
Procedure
PL
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
• 4265 Checkout
13. The
4150 Checkout
Refer to Wiring Diagram 3. Perform the following:
1. Make a print, make a copy. If the print and copy are both black, go to the
PL
Error RAP.
2. Check the ribbon cable,
PWB. If necessary, install a new CCD ribbon cable,
3. Refer to Wiring Diagram
nal assembly, PL 4.15 Item
4. If the machine prints a black configuration page, perform the following:
a. dC132 NVM Initialization.
b. Check the memory DIMM,
DIMM.
c. Perform GP 19 Memory Clear.
5. Install new components as necessary:
• CCD module, PL 14.10 Item
• HVPS, PL 1.10 Item
6. Perform the OF5 Main PWB Check RAP.
4250/4260 Checkout
Refer to Wiring Diagram 21. Perform the following:
1. Make a print, make a copy. If the print and copy are both black, go to the
Error RAP.
2. Check the ribbon cable,
PWB. If necessary, install a new CCD ribbon cable,
3. Refer to Wiring Diagram
nal assembly, PL 4.15 Item
4. If the machine prints a black configuration page, perform the following:
a. dC132 NVM Initialization.
b. Check the memory DIMM,
DIMM.
c. Perform GP 19 Memory Clear.
5. Install new components as necessary:
• CCD module, PL 14.13 Item
January 2016
3-9
WARNING
PL 14.10 Item 7 between the CCD module and CN3 on the
PL 14.10 Item
2. Check the wiring between CON1 on the
13.
PL 1.10 Item 22. If necessary, install a new memory
2.
2.
PL 14.13 Item 7 between the CCD module and CN3 on the
PL 14.13 Item
18. Check the wiring between CON2 on the
13.
PL 1.15 Item 22. If necessary, install a new memory
2.
06-100, 200 LSU
Main
7.
HVPS and the termi-
06-100, 200 LSU
Main
7.
HVPS and the termi-
Image Quality
IQ2, IQ3