Cables / Accessories - Roland R4000 Manual

Order data
12.2.3 Eddy current sensors
Order designation
EC9-8x60NF10-100-S
EC9-8x60NT10-100-S
12.2.4 Eddy current probes
Order designation
EC12x30IT10-100-S
EC20x25IT10-100-S
EC30x25IT10-100-S
EC12x40IRT10-100-S
EC5x30IF10-100-S
12.2.5 Encircling coil system
Order designation
EC13x25PDN50-500-S
KOMPLETT
Pos: 131 /Schweis snah t/Gerä te/SN D40/1 2 Be stel ldaten/Run dkörpe r/Zubehö r @ 0\mod _11 4353 238 6031 _50 1.docx @ 198 1 @ 2 @ 1
12.3

Cables / Accessories

Order designation
KNS9S-G
KNS9S-W
CECM18S-G
SKNS8S
SM18CECM18S-GG
SSB-SND40
SCB-EC-S
2299700
S0003246
2390924
2390822
*The total maximum cable length, especially when using the Sensor Switch Box must not be exceeded!
Pos: 132 /Kapite lübe rsi cht/13. An hang @ 1\mod_1 216 3651 524 21_ 501.do cx @ 65 33 @ 1 @ 1
168
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone +49 (0)7236-9392-0 · Fax +49 (0)7236-9392-33
Weld Seam Detection System R4000 SND40
for Tubes, Cans and Drums
Comment
Sensor (incl. 4 pcs. rubber mount) for NF tubes; tube diameter 10 - 250 mm;
Sensor (incl. 4 pcs. rubber mount) for NF tubes; tube diameter 10 - 250 mm;
Comment
Probe for round and flat material; axial type; track width 3 mm
Probe for round and flat material; axial type; track width 10 mm
Probe for round and flat material; axial type; track width 16 mm
Probe for round and flat material; radial type; track width 3 mm
Probe for round and flat material; axial type; track width 1.5 mm
Comment
Encircling coil system for cables and wires (cross seams);
diameter up to max. 12 mm
Comment
Cable for connecting the combo and leakage flux sensors to the control unit,
with straight cable socket, standard length 5 m, max. 25 m*
Cable for connecting the combo and leakage flux sensors to the control unit,
with angular cable socket, standard length 5 m, max. 25 m*
Cable for connecting the combo and eddy current sensors to the control unit,
standard length 5 m, max. 20 m*
Cable for connecting the combo and leakage flux sensors to the Sensor Switch Box,
with straight cable socket and cable plug, standard length 5 m, max. 20 m*
Cable for connecting the combo and eddy current sensors to the Sensor Switch Box,
with straight cable socket and cable plug, standard length 5 m, max. 15 m*
Sensor Switch Box for connecting 2 sensors
Sensor Connection Box for connecting the Eddy current probes
1 pcs. Rubber mount, for sensor NS9 / NS12
1 pcs. Rubber mount, for sensor NS24
1 pcs. Ball bearing 9x24x7 mm; for pole shoe NS9 / NS12
1 pcs. Ball bearing 8x22x7 mm; for sensor element NS9 / NS12
Manual
B0059001 / Rev. 2.3