Output Patch - Yamaha AW2816 Owner's Manual

Welcome to the world of the AW2816
2

Output patch

This section assigns output signals to OMNI OUT
jacks 1–4, the STEREO OUT jacks, DIGITAL STEREO
OUT jack, and an I/O card installed in the OPTION I/
O slot. The following output signals can be selected.
• STEREO
The output signal of the stereo bus routed through
the stereo output channel.
• BUS 1–8
The output signals of buses 1–8.
• AUX 1–6
The output signals of AUX buses 1–6.
• CH DIRECT OUT 1–8
The direct output of input channels 1–8.
• INSERT SEND
Insertion outputs for inserting internal effects into
each channel.
• RECORDER DIRECT OUT 1–16
The direct output of tracks 1–16 of the recorder sec-
tion.
Tip!
In general, these output signals can be assigned to any
output jack or output channel. For the STEREO OUT
jacks and DIGITAL STEREO OUT jacks, two adjacent
odd-numbered
be assigned.
2
STEREO
8
BUS1~8
6
AUX1~6
8
CH DIRECT OUT1~8
30
INSERT SEND
RECORDER DIRECT
16
OUT 1~16
32
even-numbered signals will always
STEREO OUT
DA
L
–10dBV
DA
R
DIGITAL STEREO
OUT
2
DITHER
COAXIAL
METER OPTION I/O SLOT
8
DITHER SLOT OUT
METER
OMNI OUT
DA
X 4
METER
0dB
DA
Internal effects 1/2
With the AW2816's default settings, the outputs of
AUX buses 5/6 are patched to the inputs of internal
effects 1/2 respectively. Also, the outputs of effects 1/2
are assigned to return channels 1/2.
If desired, you may defeat these assignments and
insert internal effects 1/2 into desired channels, or use
AUX buses 5/6 and return channels 1/2 for other pur-
poses.
AUX5(EFF1),
AUX6(EFF2)
INSERT SEND
Monitor output/headphone out-
put
For monitoring purposes, the AW2816 provides
MONITOR OUT jacks and a PHONES jack. The type
of signal that is output from these jack will change as
follows, depending on the state of the AW2816.
1 When the AW2816 is in the default state
The signal of the stereo output channel will be out-
put directly to the MONITOR OUT jacks/PHONES
jack.
B When the [SOLO] key is on
The signal of the channel selected by the [ON] key
will be sent to the SOLO bus, and will be output
from the MONITOR OUT jacks/PHONES jack.
During this time, other signals will be muted.
C When the [CUE] key is on
The direct output signal of the track selected by
the REC TRACK SELECT [1]–[16]/[ST] keys will be
output from the MONITOR OUT jacks/PHONES
jack. During this time, other signals will be muted.
D When the internal metronome is on
The metronome signal will be mixed into the out-
put signals of (1)–(3).
RECORDER
DIRECT OUT 1
RECORDER
DIRECT OUT 16
RECORDER ST Trk
DIRECT OUT L
RECORDER ST Trk
DIRECT OUT R
STEREO L
STEREO R
SOLO L
SOLO R
ON ATT
METRONOME
Tip!
• The MONITOR OUT jacks and PHONES jack always
output the same signal. However, the level adjust-
ment is independent: the output level of the MONI-
TOR OUT jacks is adjusted by the [MONITOR
OUT] control, and the output level of the PHONES
jack is adjusted by the [PHONES] control.
• If both the [SOLO] key and the [CUE] key are turned
on, only the [CUE] key will be valid.
Operation section
(EEF)
EFFECT
METER
2
EFFECT
EFFECT1/2
X 2
30
METER
(EEF)
PHONES
RECORDER
TRACK CUE
MIXER
Logic
MONITOR
SOLO Logic
DA
DA
PHONES
MONITOR
OUT
L
+4dB
R