Yamaha AW2816 Owner's Manual page 415

function number
-----------------------+------------------------+---------+---------
0x00 scene recall 0-96(memory 0-96)
0x01 eq lib recall 0-127(library 1-128)
0x02 dyn lib recall 0-127(library 1-128)
0x03 eff lib recall 0-127(library 1-128)
0x04 ch lib recall 0-64(library 0-64)
0x05 patch lib recall 0-20(library 0-20)
0x10 scene store 1-96(memory 1-99)
0x11 eq lib store 40-127(library 41-128)
0x12 dyn lib store 40-127(library 41-128)
0x13 eff lib store 41-127(library 42-128)
0x13 ch lib store 2-64(library 2-64)
0x13 patch lib store 1-20(library 1-20)
Channel 0-7(INPUT 1-8), 8-23(MONITOR 1-16), 24,25(RTN 1-2/EFF 1-2), 26(st mas)
* [0x00: scene recall] is transmitted only when you recall
a program that has not been assigned in the [Program
change table]. Normally a program change will be trans-
mitted.
4.13.3.9 Parameter Change (type 0x43:control-
ler(key remote))
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the same processing will
be performed as when the specified key (see table below)
is pressed (released)
< Transmission >
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS 11110000 F0 System Exclusive Message
ID No. 01000011 43 Manufacturer's ID
No.(YAMAHA)
SUB STATUS 0001nnnn 1n parameter change
15(MIDI Channel No.1-16)
GROUOP ID 00111110 3e MODEL ID(digital mixer)
MODEL ID 00000111 07 Device code (AW2816)
PARAM TYPE 01000011 43 controller
DATA 00000000 00 control no.(0:key remote)
0ddddddd dd No. 0-13(key 1-14)
0000dddd dd data(bit0-2:change bit
no.0-7, bit3:0=reset
1=set)
: :
EOX 11110111 F7 End Of Exclusive
KEY key no. rx/tx bit0
------+-----+-----+---------+---------+---------+---------+---------+---------+---------+---------
key1 0 rx SONG
key2 1 rx CUE
key3 2 rx FILE
key4 3 rx METER
key5 4 rx CD
key6 5 rx REC1
key7 6 rx QUICK
key8 7 rx REC2
key9 8 rx SETUP
key10 9 rx REC3
key11 10 rx UTILITY
key12 11 rx REC4
key13 12 rx MIDI
key14 13 rx REC5
You must transmit Reset (bit 3=0) after transmitting Set
(bit 3=1).
channel
0x00
0-26
0-23,26
24,25
0-26
0
0x00
0-26
0-23,26
24,25
0-26
0
n=0-
bit1 bit2 bit3
PATCH AUX3 MON9-16
REC6 REC13 AUTOMIX
VIEW AUX4 SHIFT
REC7 REC14 SCENE
PAN AUX5 F1
REC8 REC15 STORE
EQ AUX6 F2
REC9 REC16 SCENE-
DYN HOME F3
REC10 RECST SCENE+
AUX1 INPUT F4
REC11 TRACK RECALL
AUX2 MONI1-8 F5
REC12 EDIT UNDO
Appendix
Tx/Rx
Tx* /Rx
Tx/Rx
Tx/Rx
Tx/Rx
Tx/Rx
Tx/Rx
Rx only
Rx only
Rx only
Rx only
Rx only
Rx only
bit4 bit5 bit6
CTRL SEL7 ON3
REDO NUM SET
SEL1 SEL8 ON4
JOGON MARK< REPEAT
SEL2 SELST ON5
UP MAEK> A
SEL8 RELRTN1 ON6
DOWN MARK B
SEL4 SELRTN2 ON7
LEFT PUNCH ROLL
SEL5 ON1 ON8
RIGHT IN TOP
SEL6 ON2 ONST
ENTER OUT RTZ
bit7
ONRTN1
END
ONRTN2
CANCEL
SOLO
REW
REMOTE
FF
SAFE
STOP
--------
PLAY
FOOT SW
REC
413