Siemens SINAMICS S Series List Manual page 1086

Parameters
Parameters for data sets
p0392[0...n]
p0393[0...n]
p0393[0...n]
r0395[0...n]
r0396[0...n]
p0600[0...n]
p0601[0...n]
p0604[0...n]
p0605[0...n]
p0606[0...n]
p0607[0...n]
p0610[0...n]
p0616[0...n]
p0620[0...n]
p0621[0...n]
p0622[0...n]
p0625[0...n]
p0626[0...n]
p0627[0...n]
p0628[0...n]
r0630[0...n]
r0631[0...n]
r0632[0...n]
r0633[0...n]
p0643[0...n]
p0645[0...n]
p0646[0...n]
p0647[0...n]
p0648[0...n]
p0650[0...n]
p0651[0...n]
p0652[0...n]
p0653[0...n]
p0655[0...n]
p0656[0...n]
p0657[0...n]
p0658[0...n]
p0659[0...n]
p0660[0...n]
p0826[0...n]
p0827[0...n]
p1231[0...n]
p1232[0...n]
p1233[0...n]
p1234[0...n]
p1234[0...n]
p1236[0...n]
p1237[0...n]
p1909[0...n]
p1958[0...n]
p1959[0...n]
p1980[0...n]
p1981[0...n]
1-1086
Current controller adaptation, starting point KP adapted / I_adapt pt KP adap
Current controller adaptation p gain adaptation / I_adapt Kp adapt
Current controller adaptation P gain scaling / I_adapt Kp scal
Stator resistance, actual / R_stator active
Rotor resistance, actual / R_rotor active
Motor temperature sensor for monitoring / Mot temp_sensor
Motor temperature sensor type / Mot temp_sensortyp
Motor overtemperature alarm threshold / Mot TempAlrmThresh
Motor overtemperature fault threshold / MotTempFaultThresh
Motor overtemperature timer / Mot TempTimeStage
Temperature sensor fault timer / Sensor fault time
Motor overtemperature response / Mot temp response
Motor overtemperature alarm threshold 1 / Mot temp alarm 1
Thermal adaptation, stator and rotor resistance / Mot therm_adapt R
Temperature identification after restart / Temp_ident restart
Motor excitation time for temp_ident after powering-up again / t_excit temp_id
Motor ambient temperature / Mot T_ambient
Motor overtemperature, stator core / Mot T_over core
Motor overtemperature, stator winding / Mot T_over stator
Rotor winding overtemperature / Mot T_over rotor
Motor temperature model ambient temperature / MotTMod T_amb.
Motor temperature model, stator core temperature / MotTMod T_iron
Motor temperature model, stator winding temperature / MotTMod T_copper
Motor temperature model, rotor temperature / MotTMod T_rotor
Overvoltage protection for synchronous motors / Overvolt_protect
Motor-torque characteristic kT1 / Mot kT1
Motor-torque characteristic kT3 / Mot kT3
Motor-torque characteristic kT5 / Mot kT5
Motor-torque characteristic kT7 / Mot kT7
Actual motor operating hours / Mot t_oper act
Motor operating hours maintenance interval / Mot t_op maint
Motor stator resistance, scaling / Mot R_stator scal
Motor stator leakage inductance, scaling / Mot L_S_leak scal
Motor magnetizing inductance, d axis saturated scaling / Mot L_m d sat scal
Motor magnetizing inductance, q axis, saturated scaling / Mot L_m q sat scal
Motor damping inductance, d axis scaling / Mot L_damp d scal
Motor damping inductance, q axis scaling / Mot L_damp q scal
Motor damping resistance, d axis scaling / Mot R_damp d scal
Motor damping resistance, q axis scaling / Mot R_damp q scal
Motor changeover, motor number / Mot_chng mot No.
Motor changeover status word bit number / Mot_chg ZSW bitNo.
Armature short-circuit / DC brake configuration / ASC config
DC braking, braking current / DCBRK I_brake
DC braking time / DCBRK time
Speed at the start of DC braking / DCBRK n_start
DC braking, starting velocity / DCBRK v_start
Ext. armature short-cct., contactor feedback signal monit. time / ASC ext t_monit
External armature short-circuit, waiting time when opening / ASC ext t_wait
Motor data identification control word / MotID STW
Rotating measurement ramp-up/ramp-down time / MotID t_up_down
Rotating measurement configuration / Rot meas config
Pole position identification technique / PolID technique
Pole position identification maximum distance / PolID distance max
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007