Siemens SINAMICS S Series List Manual page 1071

p1513[0...n]
p1522[0...n]
p1522[0...n]
p1522[0...n]
p1523[0...n]
p1523[0...n]
p1523[0...n]
p1528[0...n]
p1528[0...n]
p1528[0...n]
p1529[0...n]
p1529[0...n]
p1529[0...n]
p1540[0...n]
p1541[0...n]
p1542[0...n]
p1542[0...n]
p1545[0...n]
p1550[0...n]
p1550[0...n]
p1551[0...n]
p1551[0...n]
p1552[0...n]
p1552[0...n]
p1554[0...n]
p1554[0...n]
p1555[0...n]
p1569[0...n]
p1569[0...n]
p1571[0...n]
p1640[0...n]
p2103[0...n]
p2104[0...n]
p2105[0...n]
p2106[0...n]
p2107[0...n]
p2108[0...n]
p2112[0...n]
p2116[0...n]
p2117[0...n]
p2144[0...n]
p2148[0...n]
p2151[0...n]
p2151[0...n]
p2154[0...n]
p2154[0...n]
p2200[0...n]
p2220[0...n]
p2221[0...n]
p2222[0...n]
p2223[0...n]
p2235[0...n]
p2236[0...n]
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007
CI: Supplementary force 2 / F_suppl 2
CI: Torque limit upper/motoring / M_max upper/mot
CI: Force limit upper/motoring / F_max upper/mot
CI: Torque limit upper / M_max upper
CI: Torque limit lower/regenerative / M_max lower/regen
CI: Force limit lower/regenerative / F_max lower/regen
CI: Torque limit lower / M_max lower
CI: Torque limit upper/motoring scaling / M_max up/mot scal
CI: Force limit upper/motoring scaling / F_max up/mot scal
CI: Torque limit upper scaling / M_max upper scal
CI: Torque limit lower/regenerating scaling / M_max low/gen scal
CI: Force limit lower/regenerative scaling / F_max low/gen scal
CI: Torque limit lower scaling / M_max lower scal
CI: Torque limit speed controller upper scaling / M_max n-ctr upScal
CI: Torque limit. speed controller lower scaling / M_max nctr lowScal
CI: Travel to fixed stop torque reduction / TfS M_red
CI: Travel to fixed stop force reduction / TfS F_red
BI: Activates travel to a fixed stop / TfS activation
BI: Transfer actual torque as torque offset / Accept act torque
BI: Transfer actual force as force offset / Accept act force
BI: Torque limit variable/fixed signal source / M_lim var/fixS_src
BI: Force limit variable/fixed signal source / F_lim var/fixS_src
CI: Torque limit upper scaling without offset / M_max up offs scal
CI: Force limit upper scaling without offset / F_max up offs scal
CI: Torque limit lower scaling without offset / M_max low offsScal
CI: Force limit lower scaling without offset / F_max low offsScal
CI: Power limit / P_max
CI: Supplementary torque 3 / M_suppl 3
CI: Supplementary force 3 / F_suppl 3
CI: Supplementary flux setpoint / Suppl flux setp
CI: Excitation current actual value / I_exc_act val
BI: 1. Acknowledge faults / 1. Acknowledge
BI: 2. Acknowledge faults / 2. Acknowledge
BI: 3. Acknowledge faults / 3. Acknowledge
BI: External fault 1 / External fault 1
BI: External fault 2 / External fault 2
BI: External fault 3 / External fault 3
BI: External alarm 1 / External alarm 1
BI: External alarm 2 / External alarm 2
BI: External alarm 3 / External alarm 3
BI: Motor stall monitoring enable (negated) / Mot stall enab neg
BI: Ramp-function generator active / HLG active
CI: Speed setpoint for messages/signals / n_set for msg
CI: Velocity setpoint for messages/signals / v_set for msg
CI: Speed setpoint 2 / n_set 2
CI: Velocity setpoint 2 / v_set 2
BI: Technology controller enable / Tec_ctrl enable
BI: Technology controller fixed value selection bit 0 / Tec_ctrl sel bit 0
BI: Technology controller fixed value selection bit 1 / Tec_ctrl sel bit 1
BI: Technology controller fixed value selection bit 2 / Tec_ctrl sel bit 2
BI: Technology controller fixed value selection bit 3 / Tec_ctrl sel bit 3
BI: Technology controller motorized potentiometer raise setpoint / Tec_ctrl mop raise
BI: Technology controller motorized potentiometer lower setpoint / Tec_ctrl mop lower
Parameters
Parameters for data sets
1-1071