Siemens SINAMICS S Series List Manual page 1070

Parameters
Parameters for data sets
p1071[0...n]
p1075[0...n]
p1076[0...n]
p1085[0...n]
p1085[0...n]
p1088[0...n]
p1088[0...n]
p1110[0...n]
p1111[0...n]
p1113[0...n]
p1122[0...n]
p1140[0...n]
p1141[0...n]
p1142[0...n]
p1142[0...n]
p1143[0...n]
p1144[0...n]
p1155[0...n]
p1155[0...n]
p1160[0...n]
p1160[0...n]
p1230[0...n]
p1235[0...n]
p1330[0...n]
p1356[0...n]
p1430[0...n]
p1430[0...n]
p1437[0...n]
p1455[0...n]
p1455[0...n]
p1466[0...n]
p1466[0...n]
p1476[0...n]
p1476[0...n]
p1477[0...n]
p1477[0...n]
p1478[0...n]
p1478[0...n]
p1479[0...n]
p1492[0...n]
p1495[0...n]
p1497[0...n]
p1497[0...n]
p1500[0...n]
p1500[0...n]
p1501[0...n]
p1501[0...n]
p1503[0...n]
p1511[0...n]
p1511[0...n]
p1512[0...n]
p1512[0...n]
p1513[0...n]
1-1070
CI: Main setpoint scaling / Main setp scal
CI: Suppl setpoint / Suppl setpoint
CI: Supplementary setpoint scaling / Suppl setp scal
CI: Speed limit in positive direction of rotation / n_limit pos
CI: Velocity limit positive direction / v_limit pos
CI: Speed limit negative direction of rotation / n_limit neg
CI: Velocity limit negative direction / n_limit neg
BI: Inhibit negative direction / Inhib neg dir rot
BI: Inhibit positive direction / Inhib pos dir rot
BI: Direction reversal / Direction reversal
BI: Bypass ramp-function generator / Bypass RFG
BI: Enables the ramp-function generator / Enable RFG
BI: Start ramp-function generator / Start RFG
BI: Enable speed setpoint / Enable n_set
BI: Enable velocity setpoint / Enable v_set
BI: Ramp-function generator, accept setting value / Accept RFG set val
CI: Ramp-function generator setting value / RFG setting value
CI: Speed controller speed setpoint 1 / n_ctrl n_set 1
CI: Velocity controller, velocity setpoint 1 / v_ctrl n_set 1
CI: Speed controller speed setpoint 2 / n_ctrl n_set 2
CI: Velocity controller, velocity setpoint 2 / v_ctrl n_set 2
BI: Armature short-circuit / DC brake activation / ASC act
BI: External armature short-circuit, contactor feedback signal / ASC ext feedback
CI: V/Hz control independent voltage setpoint / Vf V_set independ.
CI: V/f control, angular setpoint / Uf ang setpoint
CI: Speed pre-control / n_prectrl
CI: Velocity pre-control / v_prectrl
CI: Speed controller, reference model I component input / n_ctrRefMod I_comp
CI: Speed controller P gain adaptation signal / n_ctrl Adpt_sig Kp
CI: Velocity controller, P gain adaptation signal / v_ctrl Adpt_sig Kp
CI: Speed controller P-gain scaling / n_ctrl Kp scal
CI: Velocity controller P gain scaling / v_ctrl Kp scal
BI: Speed controller hold integrator / n_ctrl integ stop
BI: Velocity controller, hold integrator / v_ctrl integ stop
BI: Speed controller set integrator value / n_ctrl integ set
BI: Set velocity controller integrator value / v_ctrl integ set
CI: Speed controller integrator setting value / n_ctr integ_setVal
CI: Velocity controller, integrator value / v_ctr integ_setVal
CI: Speed controller integrator setting value scaling / n_ctrl I_val scal
BI: Droop feedback enable / Enables droop
CI: Acceleration pre-control / a_prectrl
CI: Moment of inertia, scaling / M_mom inert scal
CI: Motor weight scaling / Mot_weight scal
Macro Connector Inputs (CI) for torque setpoints / Macro CI M_set
Macro Connector Inputs (CI) for force setpoints / Macro CI F_set
BI: Change over between closed-loop speed/torque control / Changeov n/M_ctrl
BI: Changeover velocity/force control / Changeov n/F_ctrl
CI: Torque setpoint / M_set
CI: Supplementary torque 1 / M_suppl 1
CI: Supplementary force 1 / F_suppl 1
CI: Supplementary torque 1 scaling / M_suppl 1 scal
CI: Supplementary force 1 scaling / F_suppl 1 scal
CI: Supplementary torque 2 / M_suppl 2
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007