Siemens SINAMICS S Series List Manual page 1072

Parameters
Parameters for data sets
p2253[0...n]
p2254[0...n]
p2264[0...n]
p2289[0...n]
p2296[0...n]
p2297[0...n]
p2298[0...n]
p3111[0...n]
p3112[0...n]
p3784[0...n]
p3785[0...n]
p3802[0...n]
1.3.2 Parameters for Drive Data Sets (DDS)
Note:
References: /FH1/
The following list contains the drive-data-set-dependent parameters.
Product: SINAMICS S, Version: 2503100, Language: eng
p0186[0...n]
p0187[0...n]
p0188[0...n]
p0189[0...n]
p0340[0...n]
p0572[0...n]
p0578[0...n]
p0640[0...n]
p0642[0...n]
p1001[0...n]
p1001[0...n]
p1002[0...n]
p1002[0...n]
p1003[0...n]
p1003[0...n]
p1004[0...n]
p1004[0...n]
p1005[0...n]
p1005[0...n]
p1006[0...n]
p1006[0...n]
p1007[0...n]
p1007[0...n]
p1008[0...n]
p1008[0...n]
p1009[0...n]
p1009[0...n]
p1010[0...n]
1-1072
CI: Technology controller setpoint 1 / Tec_ctrl setp 1
CI: Technology controller setpoint 2 / Tec_ctrl setp 2
CI: Technology controller actual value / Tec_ctrl act val
CI: Technology controller pre-control signal / Tec_ctrl prectrl
CI: Technology controller output scaling / Tec_ctrl outp scal
CI: Technology controller maximum limiting / Tec_ctrl max_limit
CI: Technology controller minimum limiting / Tec_ctrl min_lim
BI: External fault 3, enable / Ext fault 3 enab
BI: External fault 3 enable negated / Ext flt 3 enab neg
BI: Sync-line-drive external increase voltage / Sync ext V incr
BI: Sync-line-drive external decrease voltage / Sync ext V decr
BI: Sync-line-drive enable / Sync enable
SINAMICS S120 Function Manual Drive Functions
Section "Data sets"
Motor Data Sets (MDS) number / MDS number
Encoder 1 encoder data set number / Enc 1 EDS number
Encoder 2 encoder data set number / Enc 2 EDS number
Encoder 3 encoder data set number / Enc 3 EDS number
Automatic calculation of motor/control parameters / Calc auto par
Activate inhibit list / Act inhib list
Calculate parameters that are dependent on the technology/units / Calc techn par
Current limit / Current limit
Sensorless operation current reduction / Sensorl op I_red
CO: Fixed speed setpoint 1 / n_set_fixed 1
CO: Fixed velocity setpoint 1 / n_set_fixed 1
CO: Fixed speed setpoint 2 / n_set_fixed 2
CO: Fixed velocity setpoint 2 / n_set_fixed 2
CO: Fixed speed setpoint 3 / n_set_fixed 3
CO: Fixed velocity setpoint 3 / n_set_fixed 3
CO: Fixed speed setpoint 4 / n_set_fixed 4
CO: Fixed velocity setpoint 4 / n_set_fixed 4
CO: Fixed speed setpoint 5 / n_set_fixed 5
CO: Fixed velocity setpoint 5 / n_set_fixed 5
CO: Fixed speed setpoint 6 / n_set_fixed 6
CO: Fixed velocity setpoint 6 / n_set_fixed 6
CO: Fixed speed setpoint 7 / n_set_fixed 7
CO: Fixed velocity setpoint 7 / n_set_fixed 7
CO: Fixed speed setpoint 8 / n_set_fixed 8
CO: Fixed velocity setpoint 8 / n_set_fixed 8
CO: Fixed speed setpoint 9 / n_set_fixed 9
CO: Fixed velocity setpoint 9 / n_set_fixed 9
CO: Fixed speed setpoint 10 / n_set_fixed 10
© Siemens AG 2007 All Rights Reserved
SINAMICS S List Manual (LH1), 07/2007